Copyright © SealCorp USA. All Rights Reserved | Privacy policy | Sitemap

EPDM & TPO Roofing Products Manufacturer-

    TPO Patch Disks

    • /
    • TPO Patch Disks
    TPO Patch Disks, Patch Disks, EPDM Patch Disks
    TPO Patch Disks, Patch Disks, EPDM Patch Disks

    TPO Patch Disks

    $0.00

    Download Product Data Sheet Download Safety Data Sheet

    White Patch Disks

    Product Information:

    Seal Trust™ TPO Patch Disks are uncured roofing membrane available in black or white with butyl mastic sealer die cut into 8” round disks. Can be used for flashing corners, as repair patches, or t-patches and anywhere required on EPDM, most TPO and some PVC membranes. Membrane must be cleaned prior to installation using Tape Primer.

    Application Instructions:

    TPO Patch Disks are a multi use product used in inside/outside corners, t-joint covers, and patching or repairs of both EPDM and TPO membranes. Always clean and prime membrane using roofing industry standard products for tape applications such as Seal Trust™ F-Primer or Low VOC Tape Primer. Lap Caulk should be used around all the outer edges of the disk for proper application. Use 3” steel roller for final installation step. Be careful to avoid fish mouths or air bubbles.

    SKU: https://sealtrustroofing.com/wp-content/uploads/2018/08/tpo-seam-tape.png Category: Tags: , , , , ,

    Resistant to: Weather, water & water vapor, (5) acidic or basic solutions
    Effected by: Petroleum, grease, oil, solvents, vegetable oils, and animal fats
    Product Storage: Store in warehouse without excessive heat. Do NOT store long term on roof.
    Shelf Life: 1 year if stored between 60° and 80° F.

    TPO Patch Disks Physical Properties:

    Color: White
    Solids: 100
    Odor: Slight Hydrocarbon
    Penetration: (ASTM D 217) : 100/130 mm
    Volatile: by Volume: None
    Adhesion: To most clean, dry substrates/surfaces

    Weight-201808-- lbs
    Dimensions-201808-- × -201808-- × -201808-- in

    Related products

    latex-bonding-adhesive-tpo-lba-200-5
    $0.00
    Latex Bonding Adhesive

    Download Product Data Sheet Download Safety Data Sheet

    Available in 1 gallon cans or 5 gallon pails

    Latex Bonding Adhesive Product Information:

    Seal Trust™ Latex Bonding Adhesive is a white water based adhesive used in adhering EPDM or TPO membranes to various substrates. Product goes on white and dries by evaporation to a clear film.

    Application Instructions:

    Each gallon covers approximately 100 square feet ONLY. Apply enough adhesive to roof substrate so that membrane will be coated by adhesive when rolled into it. MEMBRANE MUST BE LAID INTO WET ADHESIVE. Wrinkles may be brushed out while adhesive is still wet. ON HOT DAYS, THE ADHESIVE MAY DRY TOO FAST TO USE THIS PROCEDURE. If so apply a thin coat of adhesive to the roof surface and the back of the membrane. For highest initial bond strength join after film becomes tacky. Initial tests indicate that adhesives may be used at temperatures as low as 40F. DO NOT ALLOW MATERIAL TO FREEZE. Meets OTC VOC requirements.

    seal-trust-cover-tape
    $0.00
    Cover Tape

    Download Product Data Sheet Download Safety Data Sheet

     

    Seal Trust™ EPDM Cover Tapes are cured EPDM cover rubber with specially formulated butyl mastic extruded together for typical roofing applications such as cover for most metal terminations including gravel-stops and drip edge, and extensively used for horizontal patching, seam repairs and seam overlays. This peel and stick product has long term heat and chemical resistance and gives Seal Trust Cover Tape the ability to remain flexible in harsh conditions. Surpassing the industry standards for tack and shear strength our cover tape products provide superior holding power for long life and high durability. Industry standard roofing membrane cleaners and primers must be used to clean the membrane before application. Used with EPDM, TPO, and some PVC roofing membranes.

     

    Available in black or white

     

    Application Instructions:

    Always clean and prime membrane using roofing industry standard products for tape applications such as Seal Trust™ F-Primer or Low VOC Tape Primer. Allow primer to dry before installing tapes. Cover Tape is not for use in flashing applications. Product is a peel and stick cured cover tape. Used for covering metal termination bars, drip edge, and/or all purpose bar in seam applications etc. Apply in primed area by peeling release paper off of 6-12 inches of tape. Stick the tape onto the membrane, while continuing to pull release paper off. Make sure you start on a straight line. Continue pulling release paper off as you move down the pre-primed area. Use sharp scissors for cutting the cover tape. Use metal seam roller with some force perpendicular to tape for proper adhesion.

    ssc-600-splice-wash-1-gallon-tpo
    $0.00
    Splice Wash

    Download Product Data Sheet Download Safety Data Sheet

    Available in 1 gallon cans or 5 gallon pails

    Splice Wash is a clear solvent used to clean dirt and containments from single ply roof systems. Especially used on old membranes to remove dirt prior to application of tape primers or seam adhesives. Change rags or applicator pads frequently! Do not allow product to puddle on EPDM for long periods of time. Discarded rags should be disposed of properly and will be a flammable hazard. No smoking or open flames on the roof while using this product. Also available in a Low VOC formula for use in OTC states.

    Application Instructions:

    The use of Seal Trust™ Toluene Splice Wash prior to application of this product is recommended. This product should be scrubbed into the EPDM surface thoroughly to remove surface debris. Change applicator pads frequently and cover an area in excess of the area to be seamed. No special applicator is required. When used with clean TPO, this primer is a cleaner and primer and the use of Toluene Splice Wash is not required. Solvent resistant gloves should be used when applying this product.

    $0.00
    Splice Adhesive

    Download Product Data Sheet Download Safety Data Sheet

    Available in 1 gallon cans

    Seal Trust™ Splice Adhesive is a black adhesive designed for use as a seam adhesive during the installation of EPDM membrane systems where seaming together two sheets are required. It may also be used as a contact adhesive to bond membranes to suitable substrates as a bonding adhesive substitute. It is a viable alternative for bonding both EPDM and TPO in vertical and horizontal situations.

    Application Instructions:

    This adhesive must be thoroughly mixed prior to and during use. Recommended application instructions are printed on the container label. Meticulous care must be exercised prior to use of this product in the preparation of the seams to be lapped or spliced. The use of Seal Trust™ Splice Wash is highly recommended along with the use of Seal Trust™ Tape Primer to properly prep the seams prior to splice. Use Seal Trust™ Lap Caulk after the seams have been spliced to protect the seams until total cure has been achieved.

    stp-700-tape-primer-5-gallon
    $0.00
    Roof Tape Primer

    Download Product Data Sheet Download Safety Data Sheet

    Available in Pints (24/cs), 1 Gallon cans (6/cs), 5 Gallon pails

    Our EPDM Roof Tape Primer is a clear product specifically formulated as a primer for single ply membranes before the installation of any and all tape products such as seam, flashing and cover tapes along with pipe boots and patch disks . It is a clear product when dried allowing for use with white and black membranes. Tape Primer must be used prior to the installation of all tape products manufactured by Seal Trust™.

     

    stlvsplice-low-voc-splice-wash-tpo
    $0.00
    Low VOC Splice Wash

    Download Product Data Sheet Download Safety Data Sheet

    Available in 1 gallon cans

    Product Information:

    Splice Wash is a clear solvent used to clean dirt and containments from single ply roof systems. Especially used on old membranes to remove dirt prior to application of tape primers or seam adhesives. Change rags or applicator pads frequently! Do not allow product to puddle on EPDM or TPO for long periods of time. Discarded rags should be disposed of properly and will be a flammable hazard. No smoking or open flames on the roof while using this product. This Low VOC formula is for use in OTC states.

     

    Application Instructions:

    This product should be scrubbed into the EPDM or TPO surfaces thoroughly to remove surface debris. Change rags frequently. Always clean an area in excess of the area to be covered. When used with clean membranes such as EPDM or TPO this wash is not required. Use solvent resistant gloves when using this product.