Copyright © SealCorp USA. All Rights Reserved | Privacy policy | Sitemap

EPDM & TPO Roofing Products Manufacturer-

    Low VOC Splice Wash

    • /
    • Low VOC Splice Wash
    STLVSPICE Splice Wash
    STLVSPICE Splice Wash

    Low VOC Splice Wash

    $0.00

    Download Product Data Sheet Download Safety Data Sheet

    Available in 1 gallon cans

    Product Information:

    Splice Wash is a clear solvent used to clean dirt and containments from single ply roof systems. Especially used on old membranes to remove dirt prior to application of tape primers or seam adhesives. Change rags or applicator pads frequently! Do not allow product to puddle on EPDM or TPO for long periods of time. Discarded rags should be disposed of properly and will be a flammable hazard. No smoking or open flames on the roof while using this product. This Low VOC formula is for use in OTC states.

     

    Application Instructions:

    This product should be scrubbed into the EPDM or TPO surfaces thoroughly to remove surface debris. Change rags frequently. Always clean an area in excess of the area to be covered. When used with clean membranes such as EPDM or TPO this wash is not required. Use solvent resistant gloves when using this product.

    SKU: https://sealtrustroofing.com/wp-content/uploads/2018/08/tpo-seam-tape.png Category: Tags: , , , , , ,

    Low VOC Splice Wash Physical Properties:

    Color: Clear
    Viscosity (eps): Water thin
    Density (#/GAL.): 7.63#
    Solids: 0
    Flash Point (F): 3.9F TCC
    Base: Solvent
    Solvent System: Ester/Aromatic blend
    Clean-up Solvent: N/A
    Storage: May be stored outside if protected from water.
    Packaging: 1 gallon (6 gal/cs)

    Hazards: Extremely flammable. Avoid repeated skin contact or the breathing of concentrated vapors. Use Low VOC Splice Wash in well ventilated areas away from heat, sparks, fire, flame and ignition sources. Vapors are heavier than air and may travel a considerable distance to an ignition source and flash back. Do not inhale vapors above TLV as listed on the SDS.

    Freight Classification:  UN1133, ADHESIVE, 3 PGII NMFC# 170060 CLASS 60

    Regular Splice Wash can be found HERE.

    Weight-201808-- lbs
    Dimensions-201808-- × -201808-- × -201808-- in

    Related products

    ssc-600-splice-wash-1-gallon-tpo
    $0.00
    Splice Wash

    Download Product Data Sheet Download Safety Data Sheet

    Available in 1 gallon cans or 5 gallon pails

    Splice Wash is a clear solvent used to clean dirt and containments from single ply roof systems. Especially used on old membranes to remove dirt prior to application of tape primers or seam adhesives. Change rags or applicator pads frequently! Do not allow product to puddle on EPDM for long periods of time. Discarded rags should be disposed of properly and will be a flammable hazard. No smoking or open flames on the roof while using this product. Also available in a Low VOC formula for use in OTC states.

    Application Instructions:

    The use of Seal Trust™ Toluene Splice Wash prior to application of this product is recommended. This product should be scrubbed into the EPDM surface thoroughly to remove surface debris. Change applicator pads frequently and cover an area in excess of the area to be seamed. No special applicator is required. When used with clean TPO, this primer is a cleaner and primer and the use of Toluene Splice Wash is not required. Solvent resistant gloves should be used when applying this product.

    ssc-600-splice-wash-1-gallon-tpo
    $0.00
    Splice Wash

    Download Product Data Sheet Download Safety Data Sheet

    Available in 1 gallon cans or 5 gallon pails

    Splice Wash is a clear solvent used to clean dirt and contaminants from single ply roof systems. Especially used on old membranes to remove dirt prior to application of tape primers or seam adhesives. Change rags or applicator pads frequently! Do not allow product to puddle on EPDM for long periods of time. Discarded rags should be disposed of properly and will be a flammable hazard. No smoking or open flames on the roof while using this product. Also available in a Low VOC formula for use in OTC states.

    Application Instructions:

    The use of Seal Trust™ Toluene Splice Wash prior to application of this product is recommended. This product should be scrubbed into the EPDM surface thoroughly to remove surface debris. Change applicator pads frequently and cover an area in excess of the area to be seamed. No special applicator is required. When used with clean TPO, this primer is a cleaner and primer and the use of Toluene Splice Wash is not required. Solvent resistant gloves should be used when applying this product.

    TPO Seam Tape
    $0.00
    TPO Seam Tape

    Download Product Data Sheet Download Safety Data Sheet

    White Seam Tapes

    Seal Trust™ TPO Seam Tapes are a butyl sealer used for bonding various roofing membranes together in typical seam applications in the roofing industry. Long term heat and chemical resistance gives Seal Trust™ Seam Tape the ability to remain flexible in harsh conditions. Surpassing the industry standards for tack and shear strength our Seam Tape products provide superior holding power for long life and high durability. Used with typical roofing membranes such as EPDM, and TPO and some PVC membranes, Seam Tape allows for quick installation without expensive hot air welders. Industry standard roofing membrane cleaners and primers must be used to clean the membrane before application. Available in black or white.

    Resistant to: Weather, water & water vapor, (5) acidic or basic solutions
    Effected by: Petroleum, grease, oil, solvents, vegetable oils, and animal fats Product
    Storage: Store in warehouse without excessive heat. Do NOT store long term on roof.
    Shelf Life: 1 year if stored between 60° and 80° F.

    accessories
    $0.00
    TPO Perimeter Strip

    Download Product Data Sheet Download Safety Data Sheet

    Perimeter Strip  Information

    Seal Trust™ Perimeter Strip is a 6” wide .045 reinforced EPDM membrane to be installed under the rubber at the perimeter of roofs or at angle changes greater than 4” in height. Perimeter Strip comes with 3” butyl mastic sealer for installation to EPDM membrane using Tape Primer. Installation around the perimeter using 2”or 3” steel plates attached to the roof deck prior to installation of the membrane. Clean the back of the sheet at the area of contact with the butyl mastic. Carefully pull release paper off the mastic and press into place. Then roll membrane into mastic using steel roller for optimum results.

    Application Instructions:

    Perimeter Strip comes with 3” butyl mastic sealer for installation to EPDM membrane using Tape Primer. Install around the perimeter using 2” or 3” steel plates attached to the roof deck prior to installation of the membrane with proper fasteners spaced per recommended wind uplift area. Clean the back of the sheet at the area of contact with the butyl mastic. Carefully pull release paper off the mastic and press into place. Then roll membrane into mastic using steel roller for optimum results.

    tpo-low-voc-tape-primer-tpo-epdm
    $0.00
    Low VOC Tape Primer

    Download Product Data Sheet Download Safety Data Sheet

    Available in 1 gallon cans (6/cs)

    Low VOC Tape Primer Product Information:

    Low VOC Tape Primer is a clear product specifically formulated as a primer for single ply membranes before the installation of any and all tape products such as seam, flashing and cover tapes along with pipe boots and patch disks in all OTC states that require low VOC products. It is a clear product when dried allowing for use with white and black membranes.

    Application Instructions:
    Always use Low VOC Splice Wash on older, dirty membranes before the use of this product. Change rags frequently when cleaning dirty membranes. Low VOC Tape Primer should be scrubbed into the membrane using scrub pads such as Scotch Brite pads. Allow to dry to the touch depending on temperature and humidity. Always use solvent resistant gloves when applying this product.

    TPO Cover Tape
    $0.00
    TPO Cover Tape

    Download Product Data Sheet Download Safety Data Sheet

    White Cover Tape

    Seal Trust™ TPO Cover Tape is cured EPDM cover rubber with specially formulated butyl mastic extruded together for typical roofing applications such as cover for most metal terminations including gravel-stops and drip edge, and extensively used for horizontal patching, seam repairs and seam overlays. This peel and stick product has long term heat and chemical resistance and gives Seal Trust TPO Cover Tape the ability to remain flexible in harsh conditions. Surpassing the industry standards for tack and shear strength our cover tape products provide superior holding power for long life and high durability. Industry standard roofing membrane cleaners and primers must be used to clean the membrane before application. Used with EPDM, TPO, and some PVC roofing membranes.

    Application Instructions:

    Always clean and prime membrane using roofing industry standard products for tape applications such as Seal Trust™ F-Primer or Low VOC Tape Primer. Allow primer to dry before installing tapes. TPO Cover Tape is not for use in flashing applications. Product is a peel and stick cured cover tape. Used for covering metal termination bars, drip edge, and/or all purpose bar in seam applications etc. Apply in primed area by peeling release paper off of 6-12 inches of tape. Stick the tape onto the membrane, while continuing to pull release paper off. Make sure you start on a straight line. Continue pulling release paper off as you move down the pre-primed area. Use sharp scissors for cutting the cover tape. Use metal seam roller with some force perpendicular to tape for proper adhesion.