EPDM & TPO Roofing Products Mfg.-

    Roof Tape Primer

    • /
    • Roof Tape Primer
    Roofing Tape Primer
    Roofing Tape Primer

    Roof Tape Primer

    $0.00

    Download Product Data Sheet Download Safety Data Sheet

    Available in Pints (24/cs), 1 Gallon cans (6/cs), 5 Gallon pails

    Our TPO Roof Tape Primer is a clear product specifically formulated as a primer for single ply membranes before the installation of any and all tape products such as seam, flashing and cover tapes along with pipe boots and patch disks . It is a clear product when dried allowing for use with white and black membranes. Tape Primer must be used prior to the installation of all tape products manufactured by Seal Trust™.

    TPO Roof Tape Primer Physical Properties:

    Color: Clear to neutral
    Viscosity (eps): #3 @ 20 rpm=200cps or less
    Density (#/GAL.): 7.22# {caa914c204b1119fb3ddf612b08b76802b03c1f9b8e71b690c389a73edd07169}
    Solids: 4.8
    Flash Point (F): -25F TCC
    Base: Synthetic elastomers, resin(s) and filler(s)
    Solvent System: Aromatics and Aliphatics Clean-up
    Solvent: Mineral spirits, VMP naptha or toluene
    Storage: May be stored outside if protected from water. Packaging: Pints (24/cs), Gallons (6/cs), 5 gallon pails

    SKU: https://sealtrustroofing.com/wp-content/uploads/2018/08/tpo-seam-tape.png Category: Tags: ,

    TPO Roof Tape Primer Physical Properties:

    Color: Clear to neutral
    Viscosity (eps): #3 @ 20 rpm=200cps or less
    Density (#/GAL.): 7.23#
    Solids: 4.8
    Flash Point (F): -15F TCC
    Base: Synthetic elastomers, resin(s) and filler(s)
    Solvent System: Aromatic and Aliphatics
    Clean-up Solvent: Mineral spirits, VMP naptha or toluene
    Storage: May be stored outside if protected from water.
    Packaging: Pints (24/cs), Gallons (6 gal/cs)

    Hazards: Extremely flammable. Avoid repeated skin contact or the breathing of concentrated vapors. Use in well ventilated areas away from heat, sparks, fire, flame and ignition sources. Vapors are heavier than air and may travel a considerable distance to an ignition source and flash back. Do not inhale vapors above TLV as listed on the SDS.

    Pint & 1 Gallon Freight Classification:  UN1133, ADHESIVE, 3 PGII NMFC# 170060 CLASS 60

     

    Weight-201808-- lbs
    Dimensions-201808-- × -201808-- × -201808-- in

    Related products

    seal-trust-perimeter-strip
    $0.00
    TPO Perimeter Strip

    Download Product Data Sheet Download Safety Data Sheet

    Perimeter Strip  Information

    Seal Trust™ Perimeter Strip is a 6” wide .045 reinforced EPDM membrane to be installed under the rubber at the perimeter of roofs or at angle changes greater than 4” in height. Perimeter Strip comes with 3” butyl mastic sealer for installation to EPDM or TPO membranes using Tape Primer. Installation around the perimeter using 2”or 3” steel plates attached to the roof deck prior to installation of the membrane. Clean the back of the sheet at the area of contact with the butyl mastic. Carefully pull release paper off the mastic and press into place. Then roll membrane into mastic using steel roller for optimum results.

    Application Instructions:

    Perimeter Strip comes with 3” butyl mastic sealer for installation to EPDM membrane using Tape Primer. Install around the perimeter using 2” or 3” steel plates attached to the roof deck prior to installation of the membrane with proper fasteners spaced per recommended wind uplift area. Clean the back of the sheet at the area of contact with the butyl mastic. Carefully pull release paper off the mastic and press into place. Then roll membrane into mastic using steel roller for optimum results.

    ssc-600-splice-wash-1-gallon-tpo
    $0.00
    Splice Wash

    Download Product Data Sheet Download Safety Data Sheet

    Available in 1 gallon cans or 5 gallon pails

    Splice Wash is a clear solvent used to clean dirt and contaminants from single ply roof systems. Especially used on old membranes to remove dirt prior to application of tape primers or seam adhesives. Change rags or applicator pads frequently! Do not allow product to puddle on EPDM for long periods of time. Discarded rags should be disposed of properly and will be a flammable hazard. No smoking or open flames on the roof while using this product. Also available in a Low VOC formula for use in OTC states.

    Application Instructions:

    The use of Seal Trust™ Toluene Splice Wash prior to application of this product is recommended. This product should be scrubbed into the EPDM surface thoroughly to remove surface debris. Change applicator pads frequently and cover an area in excess of the area to be seamed. No special applicator is required. When used with clean TPO, this primer is a cleaner and primer and the use of Toluene Splice Wash is not required. Solvent resistant gloves should be used when applying this product.

    seal-trust-flashing-tapes
    $0.00
    Flashing Tapes

    Download Product Data Sheet Download Safety Data Sheet

    Product Information:

    Seal Trust™ Flashing Tapes are uncured EPDM rubber with specially formulated butyl mastic used in applications on roofs where pipes, stacks, vents, or corners require flexible flashing products to ensure no water infiltration into the roofing system. Flashing Tape allows molding or slight stretching of the material then slowly cures to form. With superior tack and peel strengths, our butyl mastic remains flexible in harsh conditions and gives a permanent water tight seal. Industry standard roofing membrane cleaners and primers must be used to clean the surfaces before application.

    Application Instructions:

    Always clean and prime membrane using roofing industry standard products for tape applications such as Seal Trust Tack Back™ Primer or Low VOC Tape Primer. Allow primer to dry before installing tapes. Field flashing corners, stacks, vents, or other roofing installation procedures where material must be formed. Do not over stretch. Not for use in horizontal seam repairs. Application by experienced roofing professionals recommended.

    nba-low-voc-bonding-adhesive-5-gallon
    $0.00
    Low VOC Neoprene Bonding Adhesive

    Download Product Data Sheet Download Safety Data Sheet

    Available in 1 gallon cans or 5 gallon pails

    Product Information:

    Seal Trust™ Low VOC Neoprene Bonding Adhesive is designed for use with EPDM and TPO membranes to adhere to insulation boards such as ISO and wood fiber and also to wood, metal, masonry and approved roofing substrates. It may also be used as a general contact bond adhesive for both vertical and horizontal surfaces. It is especially formulated for use in OTC states with Low VOC requirements. May dry faster than regular bonding adhesives due to the solvent content. May be applied using brush, roller or squeegee and also may be sprayed applied using proper equipment.

    Application Instructions:

    Recommended application instructions for use in EPDM projects are printed on the container label. Care must be taken to ensure adequate adhesive coverage when using some substrates with irregular surface patterns. Stir well before use. May be warmed to room temperature before use to promote easier application. Apply a thin coat to both intended surfaces and let adhesive “dry” until it is tacky to the touch. Mate both surfaces and apply mild pressure. Once the intended surfaces are mated, it will not be possible to reposition them without breaking the bond. Membrane should be rolled when completed. CAUTION. Keep bonding adhesive out of the seam areas at all times!

    Neo Bonding Adhesive
    $0.00
    Neoprene Bonding Adhesive

    Download Product Data Sheet Download Safety Data Sheet

    Available in 1 gallon cans or 5 gallon pails

    Neoprene Bonding Adhesive Information:

    Seal Trust™ Neoprene Bonding Adhesive is designed for use with EPDM and TPO membranes to adhere to insulation boards such as ISO and wood fiber and also to wood, metal, masonry and approved roofing substrates. It may also be used as a general contact bond adhesive for both vertical and horizontal surfaces. May be applied using brush, roller or squeegee and also may be sprayed applied using proper equipment.

    Application Instructions:

    Recommended application instructions for use in EPDM projects are printed on the container label. Care must be taken to ensure adequate adhesive coverage when using some substrates with irregular surface patterns. Stir well before use. May be warmed to room temperature before use to promote easier application. Apply a thin coat to both intended surfaces and let adhesive “dry” until it is tacky to the touch. Mate both surfaces and apply mild pressure. Once the intended surfaces are mated, it will not be possible to reposition them without breaking the bond. Membrane should be rolled when completed. CAUTION. Keep bonding adhesive out of the seam areas at all times!

    latex-bonding-adhesive-tpo-lba-200-5
    $0.00
    Latex Bonding Adhesive

    Download Product Data Sheet Download Safety Data Sheet

    Available in 1 gallon cans or 5 gallon pails

    Latex Bonding Adhesive Product Information:

    Seal Trust™ Latex Bonding Adhesive is a white water based adhesive used in adhering EPDM or TPO membranes to various substrates. Product goes on white and dries by evaporation to a clear film.

    Application Instructions:

    Each gallon covers approximately 100 square feet ONLY. Apply enough adhesive to roof substrate so that membrane will be coated by adhesive when rolled into it. MEMBRANE MUST BE LAID INTO WET ADHESIVE. Wrinkles may be brushed out while adhesive is still wet. ON HOT DAYS, THE ADHESIVE MAY DRY TOO FAST TO USE THIS PROCEDURE. If so apply a thin coat of adhesive to the roof surface and the back of the membrane. For highest initial bond strength join after film becomes tacky. Initial tests indicate that adhesives may be used at temperatures as low as 40F. DO NOT ALLOW MATERIAL TO FREEZE. Meets OTC VOC requirements.