$0.00
Download Product Data Sheet Download Safety Data Sheet
Perimeter Strip Information
Seal Trust™ Perimeter Strip is a 6” wide .045 reinforced EPDM membrane to be installed under the rubber at the perimeter of roofs or at angle changes greater than 4” in height. Perimeter Strip comes with 3” butyl mastic sealer for installation to EPDM or TPO membranes using Tape Primer. Installation around the perimeter using 2”or 3” steel plates attached to the roof deck prior to installation of the membrane. Clean the back of the sheet at the area of contact with the butyl mastic. Carefully pull release paper off the mastic and press into place. Then roll membrane into mastic using steel roller for optimum results.
Application Instructions:
Perimeter Strip comes with 3” butyl mastic sealer for installation to EPDM membrane using Tape Primer. Install around the perimeter using 2” or 3” steel plates attached to the roof deck prior to installation of the membrane with proper fasteners spaced per recommended wind uplift area. Clean the back of the sheet at the area of contact with the butyl mastic. Carefully pull release paper off the mastic and press into place. Then roll membrane into mastic using steel roller for optimum results.
Resistant to: Weather, water & water vapor, (5) acidic or basic solutions
Effected by: Petroleum, grease, oil, solvents, vegetable oils, and animal fats
Product Storage: Store in warehouse without excessive heat. Do NOT store long term on roof.
Shelf Life: 1 year if stored between 60° and 80° F.
Physical Properties:
Color: Black Solids: 100
Odor: Slight Hydrocarbon
Penetration: (ASTM D 217) : 100/130 mm
Volatile: by Volume: None
Adhesion: To most clean, dry substrates/surfaces
| Weight | -201808-- lbs |
|---|---|
| Dimensions | -201808-- × -201808-- × -201808-- in |
Download Product Data Sheet Download Safety Data Sheet
Available in 1 gallon cans or 5 gallon pails
Seal Trust™ TPO Neoprene Bonding Adhesive is designed for use with TPO membranes to adhere to insulation boards such as ISO and wood fiber and also to wood, metal, masonry and approved roofing substrates. It may also be used as a general contact bond adhesive for both vertical and horizontal surfaces. May be applied using brush, roller or squeegee and also may be sprayed applied using proper equipment.
Recommended application instructions for use in TPO projects are printed on the container label. Care must be taken to ensure adequate adhesive coverage when using some substrates with irregular surface patterns. Stir well before use. May be warmed to room temperature before use to promote easier application. Apply a thin coat to both intended surfaces and let adhesive “dry” until it is tacky to the touch. Mate both surfaces and apply mild pressure. Once the intended surfaces are mated, it will not be possible to reposition them without breaking the bond. Membrane should be rolled when completed. CAUTION. Keep bonding adhesive out of the seam areas at all times!
Download Product Data Sheet Download Safety Data Sheet
Available in 1 gallon cans or 5 gallon pails
Splice Wash is a clear solvent used to clean dirt and contaminants from single ply roof systems. Especially used on old membranes to remove dirt prior to application of tape primers or seam adhesives. Change rags or applicator pads frequently! Do not allow product to puddle on EPDM for long periods of time. Discarded rags should be disposed of properly and will be a flammable hazard. No smoking or open flames on the roof while using this product. Also available in a Low VOC formula for use in OTC states.
The use of Seal Trust™ Toluene Splice Wash prior to application of this product is recommended. This product should be scrubbed into the EPDM surface thoroughly to remove surface debris. Change applicator pads frequently and cover an area in excess of the area to be seamed. No special applicator is required. When used with clean TPO, this primer is a cleaner and primer and the use of Toluene Splice Wash is not required. Solvent resistant gloves should be used when applying this product.
Download Product Data Sheet Download Safety Data Sheet
Available in 1 gallon cans or 5 gallon pails
Product Information:
Seal Trust™ TPO Low VOC Neoprene Bonding Adhesive is designed for use with TPO membranes to adhere to insulation boards such as ISO and wood fiber and also to wood, metal, masonry and approved roofing substrates. It may also be used as a general contact bond adhesive for both vertical and horizontal surfaces. It is especially formulated for use in OTC states with Low VOC requirements. May dry faster than regular bonding adhesives due to the solvent content. May be applied using brush, roller or squeegee and also may be sprayed applied using proper equipment.
Application Instructions:
Recommended application instructions for use in TPO projects are printed on the container label. Care must be taken to ensure adequate adhesive coverage when using some substrates with irregular surface patterns. Stir well before use. May be warmed to room temperature before use to promote easier application. Apply a thin coat to both intended surfaces and let adhesive “dry” until it is tacky to the touch. Mate both surfaces and apply mild pressure. Once the intended surfaces are mated, it will not be possible to reposition them without breaking the bond. Membrane should be rolled when completed. CAUTION. Keep bonding adhesive out of the seam areas at all times!
Download Product Data Sheet Download Safety Data Sheet
Available in 1 gallon cans (6/cs)
Low VOC Tape Primer Product Information:
Low VOC Tape Primer is a clear product specifically formulated as a primer for single ply membranes before the installation of any and all tape products such as seam, flashing and cover tapes along with pipe boots and patch disks in all OTC states that require low VOC products. It is a clear product when dried allowing for use with white and black membranes.
Application Instructions:
Always use Low VOC Splice Wash on older, dirty membranes before the use of this product. Change rags frequently when cleaning dirty membranes. Low VOC Tape Primer should be scrubbed into the membrane using scrub pads such as Scotch Brite pads. Allow to dry to the touch depending on temperature and humidity. Always use solvent resistant gloves when applying this product.
Download Product Data Sheet Download Safety Data Sheet
White Patch Disks
Product Information:
Seal Trust™ TPO Patch Disks are uncured roofing membrane available in black or white with butyl mastic sealer die cut into 8” round disks. Can be used for flashing corners, as repair patches, or t-patches and anywhere required on EPDM, most TPO and some PVC membranes. Membrane must be cleaned prior to installation using Tape Primer.
Application Instructions:
TPO Patch Disks are a multi use product used in inside/outside corners, t-joint covers, and patching or repairs of both EPDM and TPO membranes. Always clean and prime membrane using roofing industry standard products for tape applications such as Seal Trust Tack Back™ Primer or Low VOC Tape Primer. Lap Caulk should be used around all the outer edges of the disk for proper application. Use 3” steel roller for final installation step. Be careful to avoid fish mouths or air bubbles.
Download Product Data Sheet Download Safety Data Sheet
White Cover Tape
Seal Trust™ TPO Cover Tape is cured EPDM cover rubber with specially formulated butyl mastic extruded together for typical roofing applications such as cover for most metal terminations including gravel-stops and drip edge, and extensively used for horizontal patching, seam repairs and seam overlays. This peel and stick product has long term heat and chemical resistance and gives Seal Trust TPO Cover Tape the ability to remain flexible in harsh conditions. Surpassing the industry standards for tack and shear strength our cover tape products provide superior holding power for long life and high durability. Industry standard roofing membrane cleaners and primers must be used to clean the membrane before application. Used with EPDM, TPO, and some PVC roofing membranes.
Application Instructions:
Always clean and prime membrane using roofing industry standard products for tape applications such as Seal Trust™ Tack Back™ Primer or Low VOC Tape Primer. Allow primer to dry before installing tapes. TPO Cover Tape is not for use in flashing applications. Product is a peel and stick cured cover tape. Used for covering metal termination bars, drip edge, and/or all purpose bar in seam applications etc. Apply in primed area by peeling release paper off of 6-12 inches of tape. Stick the tape onto the membrane, while continuing to pull release paper off. Make sure you start on a straight line. Continue pulling release paper off as you move down the pre-primed area. Use sharp scissors for cutting the cover tape. Use metal seam roller with some force perpendicular to tape for proper adhesion.
