EPDM & TPO Roofing Products Mfg.-

    Low VOC Neoprene Bonding Adhesive

    • /
    • Low VOC Neoprene Bonding Adhesive
    NBA VOC Neoprene Bonding Adhesive
    NBA VOC Neoprene Bonding Adhesive

    Low VOC Neoprene Bonding Adhesive

    $0.00

    Download Product Data Sheet Download Safety Data Sheet

    Available in 1 gallon cans or 5 gallon pails

    Product Information:

    Seal Trust™ TPO Low VOC Neoprene Bonding Adhesive is designed for use with TPO membranes to adhere to insulation boards such as ISO and wood fiber and also to wood, metal, masonry and approved roofing substrates. It may also be used as a general contact bond adhesive for both vertical and horizontal surfaces. It is especially formulated for use in OTC states with Low VOC requirements. May dry faster than regular bonding adhesives due to the solvent content. May be applied using brush, roller or squeegee and also may be sprayed applied using proper equipment.

    Application Instructions:

    Recommended application instructions for use in TPO projects are printed on the container label. Care must be taken to ensure adequate adhesive coverage when using some substrates with irregular surface patterns. Stir well before use. May be warmed to room temperature before use to promote easier application. Apply a thin coat to both intended surfaces and let adhesive “dry” until it is tacky to the touch. Mate both surfaces and apply mild pressure. Once the intended surfaces are mated, it will not be possible to reposition them without breaking the bond. Membrane should be rolled when completed. CAUTION. Keep bonding adhesive out of the seam areas at all times!

    SKU: https://sealtrustroofing.com/wp-content/uploads/2018/08/tpo-seam-tape.png Category: Tags: , , ,

    Low VOC Neoprene Bonding Adhesive Physical Properties:

    Color: Neutral to Translucent yellow
    Viscosity (eps): #3 @ 20 rpm= 2000 cps ± 400 cps
    Density (#/GAL.): 7.89#
    Solids: 22 ± 2
    Flash Point (F): 3.9F TCC
    Base: Neoprene rubber and resin(s)
    Solvent System: Aromatic and ester
    Clean-up Solvent: Methyl acetate
    Storage: May be stored outside if protected from water.
    Packaging: 1 gallon (4 gal/cs) or 5 gallon pail

    Hazards: Extremely flammable. Avoid repeated skin contact or the breathing of concentrated vapors. Use protective equipment. Use in well ventilated areas away from heat, sparks, fire, flame and ignition sources. Vapors are heavier than air and may travel a considerable distance to an ignition source and flash back. Do not inhale vapors above TLV as listed on the SDS.

    1 Gallon Freight Classification:  UN1133, ADHESIVE, 3 PGII NMFC# 170060 CLASS 60

    5 Gallon Freight Classification:  UN1133, ADHESIVE, 3 PGII NMFC# 170060 CLASS 92.5

    Low VOC Neoprene Bonding Adhesive can be used on EPDM or TPO applications.
    Weight-201808-- lbs
    Dimensions-201808-- × -201808-- × -201808-- in

    Related products

    seal-trust-tpo-white-lap-sealant
    $0.00
    Lap Caulk

    Download Product Data Sheet Download Safety Data Sheet

    White Lap Caulk
    Available in 10.5 oz. tubes

    Product Information:

    Our TPO lap caulk is available in 10.5 oz tubes in both black or white for use in single ply membrane applications such as EPDM or TPO. Standard caulk gun is required for application. Product should not be screed or smoothed after application. This caulk is meant to prevent water infiltration into seams and overlaps prior to the adhesive setting up. Usually 24-48 hours depending on temperature and humidity.

    Application Instructions:

    TPO lap caulk is used when applying splice and/ or bonding adhesives where membrane is overlapped. Prevents initial moisture infiltration before the adhesives are set. Standard caulk gun required for use. Once plastic top is cut you must puncture the tube through the plastic top with a screw driver or long screw or nail to begin application. Do not screed or smooth caulk once applied. All seams that were glued or installed should be caulked at the end of each day.

    seal-trust-perimeter-strip
    $0.00
    TPO Perimeter Strip

    Download Product Data Sheet Download Safety Data Sheet

    Perimeter Strip  Information

    Seal Trust™ Perimeter Strip is a 6” wide .045 reinforced EPDM membrane to be installed under the rubber at the perimeter of roofs or at angle changes greater than 4” in height. Perimeter Strip comes with 3” butyl mastic sealer for installation to EPDM or TPO membranes using Tape Primer. Installation around the perimeter using 2”or 3” steel plates attached to the roof deck prior to installation of the membrane. Clean the back of the sheet at the area of contact with the butyl mastic. Carefully pull release paper off the mastic and press into place. Then roll membrane into mastic using steel roller for optimum results.

    Application Instructions:

    Perimeter Strip comes with 3” butyl mastic sealer for installation to EPDM membrane using Tape Primer. Install around the perimeter using 2” or 3” steel plates attached to the roof deck prior to installation of the membrane with proper fasteners spaced per recommended wind uplift area. Clean the back of the sheet at the area of contact with the butyl mastic. Carefully pull release paper off the mastic and press into place. Then roll membrane into mastic using steel roller for optimum results.

    tpo-pipe-boots
    $0.00
    Pipe Boot

    Download Product Data Sheet Download Safety Data Sheet

    White in color and pipe sizes ranging from 1-3″ or 1-6″

    Product Information

    Seal Trust™ TPO Pipe Boot is a pre-molded roofing accessory for flashing pipes or stacks protruding from the roof on single ply membrane installations such as EPDM and TPO. Pipe Boots are installed over vent stacks and pipes usually on flat roof surfaces. The boots all come pre-taped for easy installation with a flange that installs to the membrane in a peel and stick application. The boots come with two piece release paper for easy use.

    Application Instructions:

    Always clean and prime membrane using roofing industry standard products for tape applications such as Seal Trust Tack Back™ Primer or Low VOC Tape Primer. Usual installation requires primer installed on or about 4-5 inches away from each pipe. Then measure the diameter of the pipe and cut the boot at one size smaller than the pipe (i.e. 4” stack cut at 3” level) and stretching over the pipe. Before pipe boot installation Water Cut Off Caulk should be installed on the pipe for maximum protection. Pipe clamp is provided and required for final step.

    Neo Bonding Adhesive
    $0.00
    Neoprene Bonding Adhesive

    Download Product Data Sheet Download Safety Data Sheet

    Available in 1 gallon cans or 5 gallon pails

    Neoprene Bonding Adhesive Information:

    Seal Trust™ Neoprene Bonding Adhesive is designed for use with EPDM and TPO membranes to adhere to insulation boards such as ISO and wood fiber and also to wood, metal, masonry and approved roofing substrates. It may also be used as a general contact bond adhesive for both vertical and horizontal surfaces. May be applied using brush, roller or squeegee and also may be sprayed applied using proper equipment.

    Application Instructions:

    Recommended application instructions for use in EPDM projects are printed on the container label. Care must be taken to ensure adequate adhesive coverage when using some substrates with irregular surface patterns. Stir well before use. May be warmed to room temperature before use to promote easier application. Apply a thin coat to both intended surfaces and let adhesive “dry” until it is tacky to the touch. Mate both surfaces and apply mild pressure. Once the intended surfaces are mated, it will not be possible to reposition them without breaking the bond. Membrane should be rolled when completed. CAUTION. Keep bonding adhesive out of the seam areas at all times!

    nba-low-voc-bonding-adhesive-5-gallon
    $0.00
    Low VOC Neoprene Bonding Adhesive

    Download Product Data Sheet Download Safety Data Sheet

    Available in 1 gallon cans or 5 gallon pails

    Product Information:

    Seal Trust™ Low VOC Neoprene Bonding Adhesive is designed for use with EPDM and TPO membranes to adhere to insulation boards such as ISO and wood fiber and also to wood, metal, masonry and approved roofing substrates. It may also be used as a general contact bond adhesive for both vertical and horizontal surfaces. It is especially formulated for use in OTC states with Low VOC requirements. May dry faster than regular bonding adhesives due to the solvent content. May be applied using brush, roller or squeegee and also may be sprayed applied using proper equipment.

    Application Instructions:

    Recommended application instructions for use in EPDM projects are printed on the container label. Care must be taken to ensure adequate adhesive coverage when using some substrates with irregular surface patterns. Stir well before use. May be warmed to room temperature before use to promote easier application. Apply a thin coat to both intended surfaces and let adhesive “dry” until it is tacky to the touch. Mate both surfaces and apply mild pressure. Once the intended surfaces are mated, it will not be possible to reposition them without breaking the bond. Membrane should be rolled when completed. CAUTION. Keep bonding adhesive out of the seam areas at all times!

    TPO Patch Disks
    $0.00
    Patch Disks

    Download Product Data Sheet Download Safety Data Sheet

    White Patch Disks

    Product Information:

    Seal Trust™ TPO Patch Disks are uncured roofing membrane available in black or white with butyl mastic sealer die cut into 8” round disks. Can be used for flashing corners, as repair patches, or t-patches and anywhere required on EPDM, most TPO and some PVC membranes. Membrane must be cleaned prior to installation using Tape Primer.

    Application Instructions:

    TPO Patch Disks are a multi use product used in inside/outside corners, t-joint covers, and patching or repairs of both EPDM and TPO membranes. Always clean and prime membrane using roofing industry standard products for tape applications such as Seal Trust Tack Back™ Primer or Low VOC Tape Primer. Lap Caulk should be used around all the outer edges of the disk for proper application. Use 3” steel roller for final installation step. Be careful to avoid fish mouths or air bubbles.