EPDM & TPO Roofing Products Mfg.-

    Latex Bonding Adhesive

    • /
    • Latex Bonding Adhesive
    Latex Bonding Adhesive
    Latex Bonding Adhesive

    Latex Bonding Adhesive

    $0.00

    Download Product Data Sheet Download Safety Data Sheet

    Available in 1 gallon cans or 5 gallon pails

    Latex Bonding Adhesive Product Information:

    Seal Trust™ Latex Bonding Adhesive is a white water based adhesive used in adhering EPDM or TPO membranes to various substrates. Product goes on white and dries by evaporation to a clear film.

    Application Instructions:

    Each gallon covers approximately 100 square feet ONLY. Apply enough adhesive to roof substrate so that membrane will be coated by adhesive when rolled into it. MEMBRANE MUST BE LAID INTO WET ADHESIVE. Wrinkles may be brushed out while adhesive is still wet. ON HOT DAYS, THE ADHESIVE MAY DRY TOO FAST TO USE THIS PROCEDURE. If so apply a thin coat of adhesive to the roof surface and the back of the membrane. For highest initial bond strength join after film becomes tacky. Initial tests indicate that adhesives may be used at temperatures as low as 40F. DO NOT ALLOW MATERIAL TO FREEZE. Meets OTC VOC requirements.

    SKU: https://sealtrustroofing.com/wp-content/uploads/2018/08/tpo-seam-tape.png Category: Tags: , , ,

    Physical Properties:

    Color: Milky, white liquid when wet. Clear when dry.
    Viscosity (eps): Brookfield RVF #3 spindle @ 20 rpm=3000-4000 cps
    PH: 7-8
    Density (#/GAL.): 8.7# ± .3
    Solids: 50 ± 2
    Flash Point (F): N/A
    Base: Synthetic latex polymers
    Solvent System: Water Clean-up Solvent: Water if cleaned immediately; scrape if dry.

    Storage: MINIMIZE CONTACT WITH ATMOSPHERIC AIR TO PREVENT INNOCULATION WITH MICROORGANISMS. Keep covered when not in use. Protect from freezing.

    Packaging: 1 gallon or 5 gallon pail

    Coverage: 80-100 sw. ft./gallon @ 10 wet mls. Depending on substrate.

    Hazards: Avoid inhaling concentrated vapors. Keep material from eyes. Do not Ingest.

    Freight Classification:  Non-hazardous

     

    Weight-201808-- lbs
    Dimensions-201808-- × -201808-- × -201808-- in

    Related products

    nba-low-voc-bonding-adhesive-5-gallon
    $0.00
    Low VOC Neoprene Bonding Adhesive

    Download Product Data Sheet Download Safety Data Sheet

    Available in 1 gallon cans or 5 gallon pails

    Product Information:

    Seal Trust™ TPO Low VOC Neoprene Bonding Adhesive is designed for use with TPO membranes to adhere to insulation boards such as ISO and wood fiber and also to wood, metal, masonry and approved roofing substrates. It may also be used as a general contact bond adhesive for both vertical and horizontal surfaces. It is especially formulated for use in OTC states with Low VOC requirements. May dry faster than regular bonding adhesives due to the solvent content. May be applied using brush, roller or squeegee and also may be sprayed applied using proper equipment.

    Application Instructions:

    Recommended application instructions for use in TPO projects are printed on the container label. Care must be taken to ensure adequate adhesive coverage when using some substrates with irregular surface patterns. Stir well before use. May be warmed to room temperature before use to promote easier application. Apply a thin coat to both intended surfaces and let adhesive “dry” until it is tacky to the touch. Mate both surfaces and apply mild pressure. Once the intended surfaces are mated, it will not be possible to reposition them without breaking the bond. Membrane should be rolled when completed. CAUTION. Keep bonding adhesive out of the seam areas at all times!

    ssc-600-splice-wash-1-gallon-tpo
    $0.00
    Splice Wash

    Download Product Data Sheet Download Safety Data Sheet

    Available in 1 gallon cans or 5 gallon pails

    Splice Wash is a clear solvent used to clean dirt and contaminants from single ply roof systems. Especially used on old membranes to remove dirt prior to application of tape primers or seam adhesives. Change rags or applicator pads frequently! Do not allow product to puddle on EPDM for long periods of time. Discarded rags should be disposed of properly and will be a flammable hazard. No smoking or open flames on the roof while using this product. Also available in a Low VOC formula for use in OTC states.

    Application Instructions:

    The use of Seal Trust™ Toluene Splice Wash prior to application of this product is recommended. This product should be scrubbed into the EPDM surface thoroughly to remove surface debris. Change applicator pads frequently and cover an area in excess of the area to be seamed. No special applicator is required. When used with clean TPO, this primer is a cleaner and primer and the use of Toluene Splice Wash is not required. Solvent resistant gloves should be used when applying this product.

    tpo-low-voc-tape-primer-tpo-epdm
    $0.00
    Low VOC Tape Primer

    Download Product Data Sheet Download Safety Data Sheet

    Available in 1 gallon cans (6/cs)

    Low VOC Tape Primer Product Information:

    Low VOC Tape Primer is a clear product specifically formulated as a primer for single ply membranes before the installation of any and all tape products such as seam, flashing and cover tapes along with pipe boots and patch disks in all OTC states that require low VOC products. It is a clear product when dried allowing for use with white and black membranes.

    Application Instructions:
    Always use Low VOC Splice Wash on older, dirty membranes before the use of this product. Change rags frequently when cleaning dirty membranes. Low VOC Tape Primer should be scrubbed into the membrane using scrub pads such as Scotch Brite pads. Allow to dry to the touch depending on temperature and humidity. Always use solvent resistant gloves when applying this product.

    seal-trust-quickseal-black-white-fabric-tapes-sealcorp-usa
    $0.00
    QuickSeal Tapes

    Download Product Data Sheet Download Safety Data Sheet Installation

    QuickSeal Tapes

    QuickSeal tapes from Seal Trust™ are pressure sensitive adhesive tapes, which remain flexible even in cold temperatures. QuickSeal tapes may be used on metal roofs to strip in side laps, end laps, and other penetrations prior to the application of a coating system (with the use of QuickSeal Fabric Tape). QuickSeal tapes may also be used on EPDM, TPO, CSPE/Hypalon, CPE, SBS, APP modified, asphalt BURs, all metal roofs, tiles, aluminum, galvanized steel, gypsum board, wood, polyethylene, propylene, polystyrene, fiberglass, brick, concrete, masonry and OSB. This product may be used to repair gutters, chimney flashings, and metal roofs on mobile homes and transport vehicles. QuickSeal tapes make a watertight seal. Can be installed in temperatures down to 20°F (with EPDM Tape Primer). Available in black, white, and fabric. The fabric facer is designed to be coated to match the surrounding roofing surface. The white TPO facer makes QuickSeal tapes UV resistant.

    Storage: Store in warehouse without excessive heat. Do NOT store long term on roof.
    Shelf Life: 5 years if stored between 60° and 80° F.

    seal-trust-flashing-tapes
    $0.00
    Flashing Tapes

    Download Product Data Sheet Download Safety Data Sheet

    Product Information:

    Seal Trust™ Flashing Tapes are uncured EPDM rubber with specially formulated butyl mastic used in applications on roofs where pipes, stacks, vents, or corners require flexible flashing products to ensure no water infiltration into the roofing system. Flashing Tape allows molding or slight stretching of the material then slowly cures to form. With superior tack and peel strengths, our butyl mastic remains flexible in harsh conditions and gives a permanent water tight seal. Industry standard roofing membrane cleaners and primers must be used to clean the surfaces before application.

    Application Instructions:

    Always clean and prime membrane using roofing industry standard products for tape applications such as Seal Trust Tack Back™ Primer or Low VOC Tape Primer. Allow primer to dry before installing tapes. Field flashing corners, stacks, vents, or other roofing installation procedures where material must be formed. Do not over stretch. Not for use in horizontal seam repairs. Application by experienced roofing professionals recommended.

    seal-trust-water-cut-off
    $0.00
    Water Cut-Off

    Download Product Data Sheet Download Safety Data Sheet

    Available in 10.5 oz. fiber caulk tubes or 5 gallon pails.

    Seal Trust™ Water Cut-Off Mastic is a gray solvent based caulk designed to be used under the membrane to prevent water infiltration. Meets OTC VOC requirements.

    Physical Properties:

    Color: Gray
    Viscosity (eps): 40# .104= 15-20 sec./20 gms.
    Sievers Rheometer Density (#/GAL.): 11.0#
    Solids: 86
    Flash Point (F): 14 F TCC
    Base: Synthetic elastomers, resin(s) and filler(s)
    Solvent System: Aliphatic Clean-up
    Solvent: Mineral spirits, VMP naptha, kerosene
    Storage: May be stored outside if protected from water.
    Packaging: 5 gallon pails, 10.5 oz. fiber caulk tubes (10 or 25 tubes/ctn)