Copyright © SealCorp USA. All Rights Reserved | Privacy policy | Sitemap

EPDM & TPO Roofing Products Manufacturer-

    Splice Adhesive

    • /
    • Splice Adhesive
    Splice Adhesive
    Splice Adhesive

    Splice Adhesive

    $0.00

    Download Product Data Sheet Download Safety Data Sheet

    Available in 1 gallon cans

    Seal Trust™ Splice Adhesive is a black adhesive designed for use as a seam adhesive during the installation of EPDM membrane systems where seaming together two sheets are required. It may also be used as a contact adhesive to bond membranes to suitable substrates as a bonding adhesive substitute. It is a viable alternative for bonding both EPDM and TPO in vertical and horizontal situations.

    Application Instructions:

    This adhesive must be thoroughly mixed prior to and during use. Recommended application instructions are printed on the container label. Meticulous care must be exercised prior to use of this product in the preparation of the seams to be lapped or spliced. The use of Seal Trust™ Splice Wash is highly recommended along with the use of Seal Trust™ Tape Primer to properly prep the seams prior to splice. Use Seal Trust™ Lap Caulk after the seams have been spliced to protect the seams until total cure has been achieved.

    SKU: https://sealtrustroofing.com/wp-content/uploads/2018/08/tpo-seam-tape.png Category: Tags: , , , , ,

    Physical Properties:

    Color: Black
    Viscosity (eps): #4 @ 20 rpm=2500 cps
    Density (#/GAL.): 7.11#
    Solids: 19.2
    Flash Point (F): -15F TCC
    Base: Rubber and resin(s)
    Solvent System: Aromatics and Aliphatic Clean-up
    Solvent: toluene
    Packaging: 1 gallon cans (4gal/cs)

    Storage: May be stored outside if protected from water. The adhesive is moisture sensitive and should be used immediately after opening the container. Previously used cans of splice adhesive must be thoroughly stirred and inspected before use. Once opened this products has a very limited life even inside tightly sealed containers.

    Hazards: Extremely flammable. Avoid repeated skin contact or the breathing of concentrated vapors. Use in well ventilated areas away from heat, sparks, fire, flame and ignition sources. Vapors are heavier than air and may travel a considerable distance to an ignition source and flash back. Do not inhale vapors above TLV as listed on the SDS.

    Freight Classification:  UN1133, ADHESIVE, 3 PGII NMFC# 170060 CLASS 60

     

     

    Weight-201808-- lbs
    Dimensions-201808-- × -201808-- × -201808-- in

    Related products

    tpo-low-voc-tape-primer-tpo-epdm
    $0.00
    Low VOC Tape Primer

    Download Product Data Sheet Download Safety Data Sheet

    Available in 1 gallon cans (6/cs)

    Low VOC Tape Primer Product Information:

    Low VOC Tape Primer is a clear product specifically formulated as a primer for single ply membranes before the installation of any and all tape products such as seam, flashing and cover tapes along with pipe boots and patch disks in all OTC states that require low VOC products. It is a clear product when dried allowing for use with white and black membranes.

    Application Instructions:
    Always use Low VOC Splice Wash on older, dirty membranes before the use of this product. Change rags frequently when cleaning dirty membranes. Low VOC Tape Primer should be scrubbed into the membrane using scrub pads such as Scotch Brite pads. Allow to dry to the touch depending on temperature and humidity. Always use solvent resistant gloves when applying this product.

    seal-trust-flashing-tapes_800x800
    $0.00
    Flashing Tapes

    Download Product Data Sheet Download Safety Data Sheet

    Product Information:

    Seal Trust™ Flashing Tapes are uncured EPDM rubber with specially formulated butyl mastic used in applications on roofs where pipes, stacks, vents, or corners require flexible flashing products to ensure no water infiltration into the roofing system. Flashing Tape allows molding or slight stretching of the material then slowly cures to form. With superior tack and peel strengths, our butyl mastic remains flexible in harsh conditions and gives a permanent water tight seal. Industry standard roofing membrane cleaners and primers must be used to clean the surfaces before application.

    Application Instructions:

    Always clean and prime membrane using roofing industry standard products for tape applications such as Seal Trust™ F-Primer or Low VOC Tape Primer. Allow primer to dry before installing tapes. Field flashing corners, stacks, vents, or other roofing installation procedures where material must be formed. Do not over stretch. Not for use in horizontal seam repairs. Application by experienced roofing professionals recommended.

    pipe-boot-epdm
    $0.00
    Pipe Boot

    Download Product Data Sheet Download Safety Data Sheet

    Available in Black or White and pipe sizes ranging from 1-3″ or 1-6″

    EPDM Pipe Boot  Information

    Seal Trust™ Pipe Boots are pre-molded EPDM accessory for flashing pipes or stacks protruding from the roof on single ply membrane installations such as EPDM and TPO. Pipe Boots are installed over vent stacks and pipes usually on flat roof surfaces. The boots all come pre-taped for easy installation with a flange that installs to the membrane in a peel and stick application. The boots come with two piece release paper for easy use.

    Application Instructions:

    Always clean and prime membrane using roofing industry standard products for tape applications such as Seal Trust™ F-Primer or Low VOC Tape Primer. Usual installation requires primer installed on or about 4-5 inches away from each pipe. Then measure the diameter of the pipe and cut the boot at one size smaller than the pipe (i.e. 4” stack cut at 3” level) and stretching over the pipe. Before pipe boot installation Water Cut Off Caulk should be installed on the pipe for maximum protection. Pipe clamp is provided and required for final step.

    TPO Seam Tape
    $0.00
    TPO Seam Tape

    Download Product Data Sheet Download Safety Data Sheet

    White Seam Tapes

    Seal Trust™ TPO Seam Tapes are a butyl sealer used for bonding various roofing membranes together in typical seam applications in the roofing industry. Long term heat and chemical resistance gives Seal Trust™ Seam Tape the ability to remain flexible in harsh conditions. Surpassing the industry standards for tack and shear strength our Seam Tape products provide superior holding power for long life and high durability. Used with typical roofing membranes such as EPDM, and TPO and some PVC membranes, Seam Tape allows for quick installation without expensive hot air welders. Industry standard roofing membrane cleaners and primers must be used to clean the membrane before application. Available in black or white.

    Resistant to: Weather, water & water vapor, (5) acidic or basic solutions
    Effected by: Petroleum, grease, oil, solvents, vegetable oils, and animal fats Product
    Storage: Store in warehouse without excessive heat. Do NOT store long term on roof.
    Shelf Life: 1 year if stored between 60° and 80° F.

    latex-bonding-adhesive-tpo-lba-200-5
    $0.00
    Latex Bonding Adhesive

    Download Product Data Sheet Download Safety Data Sheet

    Available in 1 gallon cans or 5 gallon pails

    Latex Bonding Adhesive Product Information:

    Seal Trust™ Latex Bonding Adhesive is a white water based adhesive used in adhering EPDM or TPO membranes to various substrates. Product goes on white and dries by evaporation to a clear film.

    Application Instructions:

    Each gallon covers approximately 100 square feet ONLY. Apply enough adhesive to roof substrate so that membrane will be coated by adhesive when rolled into it. MEMBRANE MUST BE LAID INTO WET ADHESIVE. Wrinkles may be brushed out while adhesive is still wet. ON HOT DAYS, THE ADHESIVE MAY DRY TOO FAST TO USE THIS PROCEDURE. If so apply a thin coat of adhesive to the roof surface and the back of the membrane. For highest initial bond strength join after film becomes tacky. Initial tests indicate that adhesives may be used at temperatures as low as 40F. DO NOT ALLOW MATERIAL TO FREEZE. Meets OTC VOC requirements.

    nba-low-voc-bonding-adhesive-5-gallon
    $0.00
    Low VOC Neoprene Bonding Adhesive

    Download Product Data Sheet Download Safety Data Sheet

    Available in 1 gallon cans or 5 gallon pails

    Product Information:

    Seal Trust™ TPO Low VOC Neoprene Bonding Adhesive is designed for use with TPO membranes to adhere to insulation boards such as ISO and wood fiber and also to wood, metal, masonry and approved roofing substrates. It may also be used as a general contact bond adhesive for both vertical and horizontal surfaces. It is especially formulated for use in OTC states with Low VOC requirements. May dry faster than regular bonding adhesives due to the solvent content. May be applied using brush, roller or squeegee and also may be sprayed applied using proper equipment.

    Application Instructions:

    Recommended application instructions for use in TPO projects are printed on the container label. Care must be taken to ensure adequate adhesive coverage when using some substrates with irregular surface patterns. Stir well before use. May be warmed to room temperature before use to promote easier application. Apply a thin coat to both intended surfaces and let adhesive “dry” until it is tacky to the touch. Mate both surfaces and apply mild pressure. Once the intended surfaces are mated, it will not be possible to reposition them without breaking the bond. Membrane should be rolled when completed. CAUTION. Keep bonding adhesive out of the seam areas at all times!