$0.00
Download Product Data Sheet Download Safety Data Sheet
Available in Black or White and pipe sizes ranging from 1-3″ or 1-6″
EPDM Pipe Boot Information
Seal Trust™ Pipe Boots are pre-molded EPDM accessory for flashing pipes or stacks protruding from the roof on single ply membrane installations such as EPDM and TPO. Pipe Boots are installed over vent stacks and pipes usually on flat roof surfaces. The boots all come pre-taped for easy installation with a flange that installs to the membrane in a peel and stick application. The boots come with two piece release paper for easy use.
Application Instructions:
Always clean and prime membrane using roofing industry standard products for tape applications such as Seal Trust Tack Back™ Primer or Low VOC Tape Primer. Usual installation requires primer installed on or about 4-5 inches away from each pipe. Then measure the diameter of the pipe and cut the boot at one size smaller than the pipe (i.e. 4” stack cut at 3” level) and stretching over the pipe. Before pipe boot installation Water Cut Off Caulk should be installed on the pipe for maximum protection. Pipe clamp is provided and required for final step.
Resistant to: Weather, water & water vapor, (5) acidic or basic solutions
Effected by: Petroleum, grease, oil, solvents, vegetable oils, and animal fats
Product Storage: Store in warehouse without excessive heat. Do NOT store long term on roof.
Shelf Life: 1 year if stored between 60° and 80° F.
Color: Black
Solids: 100
Odor: Slight Hydrocarbon
Penetration: (ASTM D 217) : 100/130 mm
Volatile: by Volume: None
Adhesion: To most clean, dry substrates/surfaces
| Weight | -201808-- lbs |
|---|---|
| Dimensions | -201808-- × -201808-- × -201808-- in |
Download Product Data SheetDownload Safety Data Sheet
Available in 1 gallon cans
Product Information:
Splice Wash is a clear solvent used to clean dirt and containments from single ply roof systems. Especially used on old membranes to remove dirt prior to application of tape primers or seam adhesives. Change rags or applicator pads frequently! Do not allow product to puddle on EPDM or TPO for long periods of time. Discarded rags should be disposed of properly and will be a flammable hazard. No smoking or open flames on the roof while using this product. This Low VOC formula is for use in OTC states.
Application Instructions:
This product should be scrubbed into the EPDM or TPO surfaces thoroughly to remove surface debris. Change rags frequently. Always clean an area in excess of the area to be covered. When used with clean membranes such as EPDM or TPO this wash is not required. Use solvent resistant gloves when using this product.
Download Product Data Sheet Download Safety Data Sheet
Available in Black or White
Available in 10.5 oz. tubes
Product Information:
Our EPDM Lap caulk is available in 10.5 oz tubes in both black or white for use in single ply membrane applications such as EPDM or TPO. Standard caulk gun is required for application. Product should not be screed or smoothed after application. This caulk is meant to prevent water infiltration into seams and overlaps prior to the adhesive setting up. Usually 24-48 hours depending on temperature and humidity.
Application Instructions:
Our EPDM Lap Caulk is used when applying splice and/ or bonding adhesives where membrane is overlapped. Prevents initial moisture infiltration before the adhesives are set. Standard caulk gun required for use. Once plastic top is cut you must puncture the tube through the plastic top with a screw driver or long screw or nail to begin application. Do not screed or smooth caulk once applied. All seams that were glued or installed should be caulked at the end of each day.
Download Product Data Sheet Download Safety Data Sheet Installation
QuickSeal Tapes
QuickSeal tapes from Seal Trust™ are pressure sensitive adhesive tapes, which remain flexible even in cold temperatures. QuickSeal tapes may be used on metal roofs to strip in side laps, end laps, and other penetrations prior to the application of a coating system (with the use of QuickSeal Fabric Tape). QuickSeal tapes may also be used on EPDM, TPO, CSPE/Hypalon, CPE, SBS, APP modified, asphalt BURs, all metal roofs, tiles, aluminum, galvanized steel, gypsum board, wood, polyethylene, propylene, polystyrene, fiberglass, brick, concrete, masonry and OSB. This product may be used to repair gutters, chimney flashings, and metal roofs on mobile homes and transport vehicles. QuickSeal tapes make a watertight seal. Can be installed in temperatures down to 20°F (with EPDM Tape Primer). Available in black, white, and fabric. The fabric facer is designed to be coated to match the surrounding roofing surface. The white TPO facer makes QuickSeal tapes UV resistant.
Storage: Store in warehouse without excessive heat. Do NOT store long term on roof.
Shelf Life: 5 years if stored between 60° and 80° F.
Download Product Data Sheet Download Safety Data Sheet
Available in 1 gallon cans or 5 gallon pails
Latex Bonding Adhesive Product Information:
Seal Trust™ Latex Bonding Adhesive is a water based adhesive used in adhering EPDM or TPO membranes to various substrates. Product goes on white and dries by evaporation to a clear film.
Application Instructions:
Each gallon covers approximately 100 square feet ONLY. Apply enough adhesive to roof substrate so that membrane will be coated by adhesive when rolled into it. MEMBRANE MUST BE LAID INTO WET ADHESIVE. Wrinkles may be brushed out while adhesive is still wet. ON HOT DAYS, THE ADHESIVE MAY DRY TOO FAST TO USE THIS PROCEDURE. If so apply a thin coat of adhesive to the roof surface and the back of the membrane. For highest initial bond strength join after film becomes tacky. Initial tests indicate that adhesives may be used at temperatures as low as 40F. DO NOT ALLOW MATERIAL TO FREEZE. Meets OTC VOC requirements.
Download Product Data Sheet Download Safety Data Sheet
Available in 1 gallon cans or 5 gallon pails
Product Information:
Seal Trust™ Low VOC Neoprene Bonding Adhesive is designed for use with EPDM and TPO membranes to adhere to insulation boards such as ISO and wood fiber and also to wood, metal, masonry and approved roofing substrates. It may also be used as a general contact bond adhesive for both vertical and horizontal surfaces. It is especially formulated for use in OTC states with Low VOC requirements. May dry faster than regular bonding adhesives due to the solvent content. May be applied using brush, roller or squeegee and also may be sprayed applied using proper equipment.
Application Instructions:
Recommended application instructions for use in EPDM projects are printed on the container label. Care must be taken to ensure adequate adhesive coverage when using some substrates with irregular surface patterns. Stir well before use. May be warmed to room temperature before use to promote easier application. Apply a thin coat to both intended surfaces and let adhesive “dry” until it is tacky to the touch. Mate both surfaces and apply mild pressure. Once the intended surfaces are mated, it will not be possible to reposition them without breaking the bond. Membrane should be rolled when completed. CAUTION. Keep bonding adhesive out of the seam areas at all times!
