$0.00
Download Product Data Sheet Download Safety Data Sheet
Available in Black or White
EPDM Patch Disks Information:
Seal Trust™ Patch Disks are uncured EPDM membrane available in black or white with butyl mastic sealer die cut into 8” round disks. Can be used for flashing corners, as repair patches, or t-patches and anywhere required on EPDM, most TPO and some PVC membranes. Membrane must be cleaned prior to installation using Tape Primer.
Application Instructions:
Patch Disks are a multi use product used in inside/outside corners, t-joint covers, and patching or repairs of both EPDM and TPO membranes. Always clean and prime membrane using roofing industry standard products for tape applications such as Seal Trust Tack Back™ Primer or Low VOC Tape Primer. Lap Caulk should be used around all the outer edges of the disk for proper application. Use 3” steel roller for final installation step. Be careful to avoid fish mouths or air bubbles.
Resistant to: Weather, water & water vapor, (5) acidic or basic solutions
Effected by: Petroleum, grease, oil, solvents, vegetable oils, and animal fats
Product Storage: Store in warehouse without excessive heat. Do NOT store long term on roof.
Shelf Life: 1 year if stored between 60° and 80° F.
Physical Properties:
Color: Black
Solids: 100
Odor: Slight Hydrocarbon
Penetration: (ASTM D 217) : 100/130 mm
Volatile: by Volume: None
Adhesion: To most clean, dry substrates/surfaces
| Weight | -201808-- lbs |
|---|---|
| Dimensions | -201808-- × -201808-- × -201808-- in |
Download Product Data Sheet Download Safety Data Sheet
Available in 1 gallon cans (6/cs)
Low VOC Tape Primer Product Information:
Low VOC Tape Primer is a clear product specifically formulated as a primer for single ply membranes before the installation of any and all tape products such as seam, flashing and cover tapes along with pipe boots and patch disks in all OTC states that require low VOC products. It is a clear product when dried allowing for use with white and black membranes.
Application Instructions:
Always use Low VOC Splice Wash on older, dirty membranes before the use of this product. Change rags frequently when cleaning dirty membranes. Low VOC Tape Primer should be scrubbed into the membrane using scrub pads such as Scotch Brite pads. Allow to dry to the touch depending on temperature and humidity. Always use solvent resistant gloves when applying this product.
Download Product Data Sheet Download Safety Data Sheet
Available in Pints (24/cs), 1 Gallon cans (6/cs), 5 Gallon pails
Our EPDM Roof Tape Primer is a clear product specifically formulated as a primer for single ply membranes before the installation of any and all tape products such as seam, flashing and cover tapes along with pipe boots and patch disks . It is a clear product when dried allowing for use with white and black membranes. Tape Primer must be used prior to the installation of all tape products manufactured by Seal Trust™.
Download Product Data Sheet Download Safety Data Sheet
Seal Trust™ EPDM Cover Tapes are cured EPDM cover rubber with specially formulated butyl mastic extruded together for typical roofing applications such as cover for most metal terminations including gravel-stops and drip edge, and extensively used for horizontal patching, seam repairs and seam overlays. This peel and stick product has long term heat and chemical resistance and gives Seal Trust Cover Tape the ability to remain flexible in harsh conditions. Surpassing the industry standards for tack and shear strength our cover tape products provide superior holding power for long life and high durability. Industry standard roofing membrane cleaners and primers must be used to clean the membrane before application. Used with EPDM, TPO, and some PVC roofing membranes.
Available in black or white
Application Instructions:
Always clean and prime membrane using roofing industry standard products for tape applications such as Seal Trust Tack Back™ Primer or Low VOC Tape Primer. Allow primer to dry before installing tapes. Cover Tape is not for use in flashing applications. Product is a peel and stick cured cover tape. Used for covering metal termination bars, drip edge, and/or all purpose bar in seam applications etc. Apply in primed area by peeling release paper off of 6-12 inches of tape. Stick the tape onto the membrane, while continuing to pull release paper off. Make sure you start on a straight line. Continue pulling release paper off as you move down the pre-primed area. Use sharp scissors for cutting the cover tape. Use metal seam roller with some force perpendicular to tape for proper adhesion.
Download Product Data Sheet Download Safety Data Sheet
Available in Black or White
Available in 10.5 oz. tubes
Product Information:
Our EPDM Lap caulk is available in 10.5 oz tubes in both black or white for use in single ply membrane applications such as EPDM or TPO. Standard caulk gun is required for application. Product should not be screed or smoothed after application. This caulk is meant to prevent water infiltration into seams and overlaps prior to the adhesive setting up. Usually 24-48 hours depending on temperature and humidity.
Application Instructions:
Our EPDM Lap Caulk is used when applying splice and/ or bonding adhesives where membrane is overlapped. Prevents initial moisture infiltration before the adhesives are set. Standard caulk gun required for use. Once plastic top is cut you must puncture the tube through the plastic top with a screw driver or long screw or nail to begin application. Do not screed or smooth caulk once applied. All seams that were glued or installed should be caulked at the end of each day.
Download Product Data SheetDownload Safety Data Sheet
Available in 1 gallon cans
Product Information:
Splice Wash is a clear solvent used to clean dirt and containments from single ply roof systems. Especially used on old membranes to remove dirt prior to application of tape primers or seam adhesives. Change rags or applicator pads frequently! Do not allow product to puddle on EPDM or TPO for long periods of time. Discarded rags should be disposed of properly and will be a flammable hazard. No smoking or open flames on the roof while using this product. This Low VOC formula is for use in OTC states.
Application Instructions:
This product should be scrubbed into the EPDM or TPO surfaces thoroughly to remove surface debris. Change rags frequently. Always clean an area in excess of the area to be covered. When used with clean membranes such as EPDM or TPO this wash is not required. Use solvent resistant gloves when using this product.
