EPDM & TPO Roofing Products Mfg.-

    Splice Wash

    Splice Wash SSC-600
    Splice Wash SSC-600

    Splice Wash

    $0.00

    Download Product Data Sheet Download Safety Data Sheet

    Available in 1 gallon cans or 5 gallon pails

    Splice Wash is a clear solvent used to clean dirt and containments from single ply roof systems. Especially used on old membranes to remove dirt prior to application of tape primers or seam adhesives. Change rags or applicator pads frequently! Do not allow product to puddle on EPDM for long periods of time. Discarded rags should be disposed of properly and will be a flammable hazard. No smoking or open flames on the roof while using this product. Also available in a Low VOC formula for use in OTC states.

    Application Instructions:

    The use of Seal Trust™ Toluene Splice Wash prior to application of this product is recommended. This product should be scrubbed into the EPDM surface thoroughly to remove surface debris. Change applicator pads frequently and cover an area in excess of the area to be seamed. No special applicator is required. When used with clean TPO, this primer is a cleaner and primer and the use of Toluene Splice Wash is not required. Solvent resistant gloves should be used when applying this product.

    SKU: https://sealtrustroofing.com/wp-content/uploads/2018/08/tpo-seam-tape.png Category: Tags: ,

    Physical Properties:

    Color: Clear
    Viscosity (eps): Water thin
    Density (#/GAL.): 7.25#
    Solids: 0
    Flash Point (F): 39F TCC
    Base: Aromatic solvent
    Solvent System: Aromatic Clean-up Solvent: N/A
    Storage: May be stored outside if protected from water. Packaging: 1 gallon (6 gal/cs) or 5 gallon pail

    Hazards: Extremely flammable. Avoid repeated skin contact or the breathing of concentrated vapors. Use in well ventilated areas away from heat, sparks, fire, flame and ignition sources. Vapors are heavier than air and may travel a considerable distance to an ignition source and flash back. Do not inhale vapors above TLV as listed on the SDS.

    1 Gallon Freight Classification:  UN1133, ADHESIVE, 3 PGII NMFC# 170060 CLASS 60

    5 Gallon Freight Classification:  UN1133, ADHESIVE, 3 PGII NMFC# 170060 CLASS 92.5

    Available in 1 gallon cans or 5 gallon pails

     

    Weight-201808-- lbs
    Dimensions-201808-- × -201808-- × -201808-- in

    Related products

    seal-trust-tpo-white-lap-sealant
    $0.00
    Lap Caulk

    Download Product Data Sheet Download Safety Data Sheet

    White Lap Caulk
    Available in 10.5 oz. tubes

    Product Information:

    Our TPO lap caulk is available in 10.5 oz tubes in both black or white for use in single ply membrane applications such as EPDM or TPO. Standard caulk gun is required for application. Product should not be screed or smoothed after application. This caulk is meant to prevent water infiltration into seams and overlaps prior to the adhesive setting up. Usually 24-48 hours depending on temperature and humidity.

    Application Instructions:

    TPO lap caulk is used when applying splice and/ or bonding adhesives where membrane is overlapped. Prevents initial moisture infiltration before the adhesives are set. Standard caulk gun required for use. Once plastic top is cut you must puncture the tube through the plastic top with a screw driver or long screw or nail to begin application. Do not screed or smooth caulk once applied. All seams that were glued or installed should be caulked at the end of each day.

    seal-trust-flashing-tapes
    $0.00
    Flashing Tapes

    Download Product Data Sheet Download Safety Data Sheet

    Product Information:

    Seal Trust™ Flashing Tapes are uncured EPDM rubber with specially formulated butyl mastic used in applications on roofs where pipes, stacks, vents, or corners require flexible flashing products to ensure no water infiltration into the roofing system. Flashing Tape allows molding or slight stretching of the material then slowly cures to form. With superior tack and peel strengths, our butyl mastic remains flexible in harsh conditions and gives a permanent water tight seal. Industry standard roofing membrane cleaners and primers must be used to clean the surfaces before application.

    Application Instructions:

    Always clean and prime membrane using roofing industry standard products for tape applications such as Seal Trust Tack Back™ Primer or Low VOC Tape Primer. Allow primer to dry before installing tapes. Field flashing corners, stacks, vents, or other roofing installation procedures where material must be formed. Do not over stretch. Not for use in horizontal seam repairs. Application by experienced roofing professionals recommended.

    Splice Adhesive
    $0.00
    Splice Adhesive

    Download Product Data Sheet Download Safety Data Sheet

    Available in 1 gallon cans

    Seal Trust™ Splice Adhesive is a black adhesive designed for use as a seam adhesive during the installation of EPDM membrane systems where seaming together two sheets are required. It may also be used as a contact adhesive to bond membranes to suitable substrates as a bonding adhesive substitute. It is a viable alternative for bonding both EPDM and TPO in vertical and horizontal situations.

    Application Instructions:

    This adhesive must be thoroughly mixed prior to and during use. Recommended application instructions are printed on the container label. Meticulous care must be exercised prior to use of this product in the preparation of the seams to be lapped or spliced. The use of Seal Trust™ Splice Wash is highly recommended along with the use of Seal Trust™ Tape Primer to properly prep the seams prior to splice. Use Seal Trust™ Lap Caulk after the seams have been spliced to protect the seams until total cure has been achieved.

    TPO Seam Tape
    $0.00
    Seam Tape

    Download Product Data Sheet Download Safety Data Sheet

    White Seam Tapes

    Seal Trust™ TPO Seam Tapes are a butyl sealer used for bonding various roofing membranes together in typical seam applications in the roofing industry. Long term heat and chemical resistance gives Seal Trust™ Seam Tape the ability to remain flexible in harsh conditions. Surpassing the industry standards for tack and shear strength our Seam Tape products provide superior holding power for long life and high durability. Used with typical roofing membranes such as EPDM, and TPO and some PVC membranes, Seam Tape allows for quick installation without expensive hot air welders. Industry standard roofing membrane cleaners and primers must be used to clean the membrane before application. Available in black or white.

    Resistant to: Weather, water & water vapor, (5) acidic or basic solutions
    Effected by: Petroleum, grease, oil, solvents, vegetable oils, and animal fats Product
    Storage: Store in warehouse without excessive heat. Do NOT store long term on roof.
    Shelf Life: 1 year if stored between 60° and 80° F.

    seal-trust-quickseal-black-white-fabric-tapes-sealcorp-usa
    $0.00
    QuickSeal Tapes

    Download Product Data Sheet Download Safety Data Sheet Installation

    QuickSeal Tapes

    QuickSeal tapes from Seal Trust™ are pressure sensitive adhesive tapes, which remain flexible even in cold temperatures. QuickSeal tapes may be used on metal roofs to strip in side laps, end laps, and other penetrations prior to the application of a coating system (with the use of QuickSeal Fabric Tape). QuickSeal tapes may also be used on EPDM, TPO, CSPE/Hypalon, CPE, SBS, APP modified, asphalt BURs, all metal roofs, tiles, aluminum, galvanized steel, gypsum board, wood, polyethylene, propylene, polystyrene, fiberglass, brick, concrete, masonry and OSB. This product may be used to repair gutters, chimney flashings, and metal roofs on mobile homes and transport vehicles. QuickSeal tapes make a watertight seal. Can be installed in temperatures down to 20°F (with EPDM Tape Primer). Available in black, white, and fabric. The fabric facer is designed to be coated to match the surrounding roofing surface. The white TPO facer makes QuickSeal tapes UV resistant.

    Storage: Store in warehouse without excessive heat. Do NOT store long term on roof.
    Shelf Life: 5 years if stored between 60° and 80° F.

    seal-trust-epdm-patch-disks
    $0.00
    Patch Disks

    Download Product Data Sheet Download Safety Data Sheet

    Available in Black or White

    EPDM Patch Disks Information:

    Seal Trust™ Patch Disks are uncured EPDM membrane available in black or white with butyl mastic sealer die cut into 8” round disks. Can be used for flashing corners, as repair patches, or t-patches and anywhere required on EPDM, most TPO and some PVC membranes. Membrane must be cleaned prior to installation using Tape Primer.

    Application Instructions:

    Patch Disks are a multi use product used in inside/outside corners, t-joint covers, and patching or repairs of both EPDM and TPO membranes. Always clean and prime membrane using roofing industry standard products for tape applications such as Seal Trust Tack Back™ Primer or Low VOC Tape Primer. Lap Caulk should be used around all the outer edges of the disk for proper application. Use 3” steel roller for final installation step. Be careful to avoid fish mouths or air bubbles.