bonding adhesive Archives

$latex-bonding-adhesive-tpo-lba-200-5$

$0.00

Download Product Data Sheet Download Safety Data Sheet

Available in 1 gallon cans or 5 gallon pails

Latex Bonding Adhesive Product Information:

Seal Trust™ Latex Bonding Adhesive is a white water based adhesive used in adhering EPDM or TPO membranes to various substrates. Product goes on white and dries by evaporation to a clear film.

Application Instructions:

Each gallon covers approximately 100 square feet ONLY. Apply enough adhesive to roof substrate so that membrane will be coated by adhesive when rolled into it. MEMBRANE MUST BE LAID INTO WET ADHESIVE. Wrinkles may be brushed out while adhesive is still wet. ON HOT DAYS, THE ADHESIVE MAY DRY TOO FAST TO USE THIS PROCEDURE. If so apply a thin coat of adhesive to the roof surface and the back of the membrane. For highest initial bond strength join after film becomes tacky. Initial tests indicate that adhesives may be used at temperatures as low as 40F. DO NOT ALLOW MATERIAL TO FREEZE. Meets OTC VOC requirements.

$0.00

Low VOC Neoprene Bonding Adhesive

Download Product Data Sheet Download Safety Data Sheet

Available in 1 gallon cans or 5 gallon pails

Product Information:

Seal Trust™ TPO Low VOC Neoprene Bonding Adhesive is designed for use with TPO membranes to adhere to insulation boards such as ISO and wood fiber and also to wood, metal, masonry and approved roofing substrates. It may also be used as a general contact bond adhesive for both vertical and horizontal surfaces. It is especially formulated for use in OTC states with Low VOC requirements. May dry faster than regular bonding adhesives due to the solvent content. May be applied using brush, roller or squeegee and also may be sprayed applied using proper equipment.

Application Instructions:

Recommended application instructions for use in TPO projects are printed on the container label. Care must be taken to ensure adequate adhesive coverage when using some substrates with irregular surface patterns. Stir well before use. May be warmed to room temperature before use to promote easier application. Apply a thin coat to both intended surfaces and let adhesive “dry” until it is tacky to the touch. Mate both surfaces and apply mild pressure. Once the intended surfaces are mated, it will not be possible to reposition them without breaking the bond. Membrane should be rolled when completed. CAUTION. Keep bonding adhesive out of the seam areas at all times!

$0.00

Low VOC Neoprene Bonding Adhesive

Download Product Data Sheet Download Safety Data Sheet

Available in 1 gallon cans or 5 gallon pails

Product Information:

Seal Trust™ Low VOC Neoprene Bonding Adhesive is designed for use with EPDM and TPO membranes to adhere to insulation boards such as ISO and wood fiber and also to wood, metal, masonry and approved roofing substrates. It may also be used as a general contact bond adhesive for both vertical and horizontal surfaces. It is especially formulated for use in OTC states with Low VOC requirements. May dry faster than regular bonding adhesives due to the solvent content. May be applied using brush, roller or squeegee and also may be sprayed applied using proper equipment.

Application Instructions:

Recommended application instructions for use in EPDM projects are printed on the container label. Care must be taken to ensure adequate adhesive coverage when using some substrates with irregular surface patterns. Stir well before use. May be warmed to room temperature before use to promote easier application. Apply a thin coat to both intended surfaces and let adhesive “dry” until it is tacky to the touch. Mate both surfaces and apply mild pressure. Once the intended surfaces are mated, it will not be possible to reposition them without breaking the bond. Membrane should be rolled when completed. CAUTION. Keep bonding adhesive out of the seam areas at all times!

$0.00

Neoprene Bonding Adhesive

Download Product Data Sheet Download Safety Data Sheet

Available in 1 gallon cans or 5 gallon pails

Product Information:

Seal Trust™ TPO Neoprene Bonding Adhesive is designed for use with TPO membranes to adhere to insulation boards such as ISO and wood fiber and also to wood, metal, masonry and approved roofing substrates. It may also be used as a general contact bond adhesive for both vertical and horizontal surfaces. May be applied using brush, roller or squeegee and also may be sprayed applied using proper equipment.

Application Instructions:

Recommended application instructions for use in TPO projects are printed on the container label. Care must be taken to ensure adequate adhesive coverage when using some substrates with irregular surface patterns. Stir well before use. May be warmed to room temperature before use to promote easier application. Apply a thin coat to both intended surfaces and let adhesive “dry” until it is tacky to the touch. Mate both surfaces and apply mild pressure. Once the intended surfaces are mated, it will not be possible to reposition them without breaking the bond. Membrane should be rolled when completed. CAUTION. Keep bonding adhesive out of the seam areas at all times!

$0.00

Neoprene Bonding Adhesive

Download Product Data Sheet Download Safety Data Sheet

Available in 1 gallon cans or 5 gallon pails

Neoprene Bonding Adhesive Information:

Seal Trust™ Neoprene Bonding Adhesive is designed for use with EPDM and TPO membranes to adhere to insulation boards such as ISO and wood fiber and also to wood, metal, masonry and approved roofing substrates. It may also be used as a general contact bond adhesive for both vertical and horizontal surfaces. May be applied using brush, roller or squeegee and also may be sprayed applied using proper equipment.

Application Instructions:

Recommended application instructions for use in EPDM projects are printed on the container label. Care must be taken to ensure adequate adhesive coverage when using some substrates with irregular surface patterns. Stir well before use. May be warmed to room temperature before use to promote easier application. Apply a thin coat to both intended surfaces and let adhesive “dry” until it is tacky to the touch. Mate both surfaces and apply mild pressure. Once the intended surfaces are mated, it will not be possible to reposition them without breaking the bond. Membrane should be rolled when completed. CAUTION. Keep bonding adhesive out of the seam areas at all times!