Copyright All Rights Reserved © 2022 | Privacy policy | Sitemap

Home

[mk_page_section full_width=”true” padding_top=”0″ padding_bottom=”0″ sidebar=”sidebar-1″]

[mk_revslider id=”home”]
[/mk_page_section][mk_page_section sidebar=”sidebar-1″]

EPDM Rubber and TPO Roofing Accessories You Can Trust!

Seal Trust roofing accessories are for use in installation, repair and maintenance of EPDM rubber and TPO roofs.

Seal Trust is a respected roofing tape and accessories brand, offering a complete line of wholesale tapes, adhesives and accessories for installation and repair of single ply membranes.

Our Seal Trust line of  single ply accessories consist of both short length rolls ideal for single use projects, and also include 100 Ft rolls for industry standard lengths.  Seal Trust’s complete product line allows large and small contractors to purchase only what they require for each project.  And whether they need adhesives, primers or caulks, it’s very important that these products be high quality and durable.  Each Seal Trust product meets or exceeds roofing industry standards.  But because of cost savings at our two manufacturing facilities in Indiana, your distributor cost savings are substantial.  Helping distributors make more profits gives you the opportunity to grow your business.  Our very first roofing distributor customers are still  some of our best customers and friends.

[/mk_page_section][mk_page_section bg_color=”#f4f4f4″ border_color=”#e8e8e8″ sidebar=”sidebar-1″]

 Our Products

$0.00

Download Product Data Sheet Download Safety Data Sheet

Available in 1 gallon cans or 5 gallon pails

Splice Wash is a clear solvent used to clean dirt and containments from single ply roof systems. Especially used on old membranes to remove dirt prior to application of tape primers or seam adhesives. Change rags or applicator pads frequently! Do not allow product to puddle on EPDM for long periods of time. Discarded rags should be disposed of properly and will be a flammable hazard. No smoking or open flames on the roof while using this product. Also available in a Low VOC formula for use in OTC states.

Application Instructions:

The use of Seal Trust™ Toluene Splice Wash prior to application of this product is recommended. This product should be scrubbed into the EPDM surface thoroughly to remove surface debris. Change applicator pads frequently and cover an area in excess of the area to be seamed. No special applicator is required. When used with clean TPO, this primer is a cleaner and primer and the use of Toluene Splice Wash is not required. Solvent resistant gloves should be used when applying this product.

$0.00

Download Product Data Sheet Download Safety Data Sheet

Available in 1 gallon cans (6/cs)

Low VOC Tape Primer Product Information:

Low VOC Tape Primer is a clear product specifically formulated as a primer for single ply membranes before the installation of any and all tape products such as seam, flashing and cover tapes along with pipe boots and patch disks in all OTC states that require low VOC products. It is a clear product when dried allowing for use with white and black membranes.

Application Instructions:
Always use Low VOC Splice Wash on older, dirty membranes before the use of this product. Change rags frequently when cleaning dirty membranes. Low VOC Tape Primer should be scrubbed into the membrane using scrub pads such as Scotch Brite pads. Allow to dry to the touch depending on temperature and humidity. Always use solvent resistant gloves when applying this product.

$0.00

Download Product Data Sheet Download Safety Data Sheet

Available in 10.5 oz. fiber caulk tubes or 5 gallon pails.

Seal Trust™ Water Cut-Off Mastic is a gray solvent based caulk designed to be used under the membrane to prevent water infiltration. Meets OTC VOC requirements.

Physical Properties:

Color: Gray
Viscosity (eps): 40# .104= 15-20 sec./20 gms.
Sievers Rheometer Density (#/GAL.): 11.0#
{caa914c204b1119fb3ddf612b08b76802b03c1f9b8e71b690c389a73edd07169} Solids: 86
Flash Point (F): 14 F TCC
Base: Synthetic elastomers, resin(s) and filler(s)
Solvent System: Aliphatic Clean-up
Solvent: Mineral spirits, VMP naptha, kerosene
Storage: May be stored outside if protected from water.
Packaging: 5 gallon pails, 10.5 oz. fiber caulk tubes (10 or 25 tubes/ctn)

$0.00

Download Product Data Sheet Download Safety Data Sheet

Available in Black or White
Available in 10.5 oz. tubes

Product Information:

Our EPDM Lap caulk is available in 10.5 oz tubes in both black or white for use in single ply membrane applications such as EPDM or TPO. Standard caulk gun is required for application. Product should not be screed or smoothed after application. This caulk is meant to prevent water infiltration into seams and overlaps prior to the adhesive setting up. Usually 24-48 hours depending on temperature and humidity.

Application Instructions:

Our EPDM Lap Caulk is used when applying splice and/ or bonding adhesives where membrane is overlapped. Prevents initial moisture infiltration before the adhesives are set. Standard caulk gun required for use. Once plastic top is cut you must puncture the tube through the plastic top with a screw driver or long screw or nail to begin application. Do not screed or smooth caulk once applied. All seams that were glued or installed should be caulked at the end of each day.

$0.00

Download Product Data Sheet Download Safety Data Sheet

Available in 1 gallon cans or 5 gallon pails

Latex Bonding Adhesive Product Information:

Seal Trust™ Latex Bonding Adhesive is a water based adhesive used in adhering EPDM or TPO membranes to various substrates. Product goes on white and dries by evaporation to a clear film.

Application Instructions:

Each gallon covers approximately 100 square feet ONLY. Apply enough adhesive to roof substrate so that membrane will be coated by adhesive when rolled into it. MEMBRANE MUST BE LAID INTO WET ADHESIVE. Wrinkles may be brushed out while adhesive is still wet. ON HOT DAYS, THE ADHESIVE MAY DRY TOO FAST TO USE THIS PROCEDURE. If so apply a thin coat of adhesive to the roof surface and the back of the membrane. For highest initial bond strength join after film becomes tacky. Initial tests indicate that adhesives may be used at temperatures as low as 40F. DO NOT ALLOW MATERIAL TO FREEZE. Meets OTC VOC requirements.

$0.00

Download Product Data Sheet Download Safety Data Sheet

QuickSeal Tapes

QuickSeal tapes from Seal Trust™ are pressure sensitive adhesive tapes, which remain flexible even in cold temperatures. QuickSeal tapes may be used on metal roofs to strip in side laps, end laps, and other penetrations prior to the application of a coating system (with the use of QuickSeal Fabric Tape). QuickSeal tapes may also be used on EPDM, TPO, CSPE/Hypalon, CPE, SBS, APP modified, asphalt BURs, all metal roofs, tiles, aluminum, galvanized steel, gypsum board, wood, polyethylene, propylene, polystyrene, fiberglass, brick, concrete, masonry and OSB. This product may be used to repair gutters, chimney flashings, and metal roofs on mobile homes and transport vehicles. QuickSeal tapes make a watertight seal. Can be installed in temperatures down to 20°F (with EPDM Tape Primer). Available in black, white, and fabric. The fabric facer is designed to be coated to match the surrounding roofing surface. The white TPO facer makes QuickSeal tapes UV resistant.

Storage: Store in warehouse without excessive heat. Do NOT store long term on roof.
Shelf Life: 5 years if stored between 60° and 80° F.

[/mk_page_section]