Home > FAQs
Seal Trust Contact Adhesive adheres EPDM membranes to various surfaces. It works with insulation boards (like ISO and wood fiber), wood, metal, masonry, and approved low-slope roofing substrates. You can also use it as a general contact adhesive for both vertical and horizontal surfaces.
Seal Trust lap caulk seals overlapping low-slope roofing membranes. Apply it when using splice or bonding adhesives. It stops initial moisture before the adhesives set.
Seal Trust Latex Bonding Adhesive adheres EPDM or TPO membranes to various surfaces. This white, water-based roofing adhesive dries clear through evaporation.
Seal Trust Neoprene Bonding Adhesive attaches EPDM and TPO membranes to insulation boards. It works with ISO, wood fiber, wood, metal, masonry, and approved low-slope roofing substrates. You can also use it as a general contact adhesive for vertical and horizontal surfaces.
Seal Trust Low VOC Neoprene Bonding Adhesive is especially formulated for use in OTC states with Low VOC requirements. It may dry faster than regular bonding adhesives due to the solvent content. Our Low VOC Neoprene Bonding Adhesive is designed for use with TPO & EPDM membranes to adhere to insulation boards such as ISO and wood fiber and also to wood, metal, masonry and approved low slope roofing substrates. It may also be used as a general contact bond adhesive for both vertical and horizontal surfaces.
Seal Trust Splice Wash is a clear solvent. It cleans dirt and contaminants from single-ply, low-slope roof systems. Indeed, it works very effectively on old membranes. Use it to remove dirt before applying tape primers or seam adhesives.
Seal Trust Low VOC Splice Wash is a clear solvent. It cleans dirt and containments from single ply roof systems. Specifically, It works very effectively on old membranes to remove dirt prior to application of tape primers or seam adhesives. Furthermore, our Low VOC Splice Wash is specially formulated for use in OTC (Ozone Transport Commission) states with Low VOC requirements.
Seal Trust Splice Adhesive is a black adhesive. It creates seams during EPDM membrane system installations, joining two sheets. Additionally, you can use it as a contact adhesive. It bonds membranes to suitable substrates, replacing a standard bonding adhesive. Therefore, it offers a viable alternative for bonding both EPDM and TPO in vertical and horizontal applications.
Seal Trust Tape Primer is another clear product. It primes single-ply membranes before you install tape products like seam tape, flashing tapes, and cover tapes. It also works with pipe boots and patch disks in OTC states that require low VOC products. As a result, it dries clear, making it suitable for both white TPO and black EPDM roofing membranes.
Seal Trust Low VOC Tape Primer is a clear product specifically formulated as a primer for single ply membranes before the installation of any and all tape products such as seam tape, flashing tapes and cover tapes along with pipe boots and patch disks in all OTC states that require low VOC products. It is a clear product when dried allowing for use with white TPO and black EPDM roofing membranes.
Seal Trust Tack Back F-Primer is a black tape primer. It enhances the performance and bond of EPDM seam tape during EPDM rubber roofing installations. Remember, stir this roofing tape primer at the start of each day and periodically throughout the day. It dries quickly, but temperature and humidity influence its drying time. Ultimately, strong initial tack allows tapes to bond immediately to membranes.
Seal Trust Water Cut-Off is a gray, solvent-based caulk. It prevents water infiltration when you apply it under the membrane.
Use industrial-quality, non-treated roof insulation board, OSB board (rough side up), untreated plywood, or non-foil-faced Polyiso board. Please contact us if you have questions using the contact form.
Yes, but avoid ripping or puncturing the membrane with sharp items when walking on it.
Yes, the carpet manufacturer should be contacted for guidance. It is important to keep in mind that certain adhesives may compromise the EPDM membrane’s durability or reduce its effectiveness.
Use our Neoprene Bonding Adhesive or Splice Adhesive for any slope greater than a 2-inch per 12-inch pitch.
Maintain a minimum temperature of 40 degrees. This temperature must remain until at least 72 hours after project completion.
Yes, you can use any Seal Trust adhesive with the two-sided method. For this installation, apply the adhesive to both the substrate and the membrane. Wait for it to dry to the touch, and then bond them together.
All Seal Trust adhesives work with EPDM membranes. However, not all Seal Trust adhesives are suitable for TPO. Contact us with any further questions.
When applying roofing adhesive, ensure it dries to the touch. Otherwise, it will blister, preventing a smooth finish. If your substrate is porous, the blisters will eventually dissipate. However, if it is not porous, the blisters will remain visible. This could cause drainage issues for your roof.
Also, avoid using too little adhesive. Apply solvent-based adhesive at a minimum of 60 square feet per gallon. Apply water-based adhesives at 100 square feet per gallon.
Yes, use either Seal Trust Neoprene Bonding Adhesive or Seal Trust Splice Adhesive. When using these adhesives, apply them with the contact/two-sided method. First, apply the adhesive to both the substrate and the membrane. Then, wait for it to dry to the touch. Finally, bond them together.
There are two types of adhesives.
Yes, you can use Seal Trust Splice Adhesive for this. We only recommend using Splice Adhesive to adhere EPDM to EPDM on the seams. Once you adhere the EPDM, we strongly urge using Seal Trust Cover Tape over the seam. This adds extra reinforcement. EPDM seams can expand and contract during weather changes, which might cause the seam to come apart.
Any of these Seal Trust Adhesives will work:
Seal Trust Water Cut Off Caulk seals roofing membranes to prevent water penetration. It works well at drain terminations and behind all-purpose bars at wall terminations. Primarily, it acts as a sealing agent between the EPDM membrane and its termination point or attachment.
Seal Trust Black and White Lap Caulks are specially formulated, high-solids, EPDM-based sealants. They seal the exposed edges of rubber membrane splices in EPDM roof systems. Primarily, lap sealant seals the membrane’s exposed edges. It is extremely durable. Its cured rubber consistency allows it to expand and contract with the membrane.
All Seal Trust brand primers primarily clean and prepare the EPDM surface. Do this before adhering any Seal Trust Tapes and other accessories to the membrane. This product is mandatory.
No, Seal Trust Latex Bonding Adhesive is not waterproof after it dries. If an EPDM adhesive is needed that needs to be waterproof after drying, we recommend our Seal Trust Splice Adhesive.
Seal Trust QuickSeal Tapes are being used to repair gutters, chimney flashings, and metal roofs on mobile homes and transport vehicles. QuickSeal tapes are also being used on metal roofs to strip in side laps, end laps, and other penetrations prior to the application of a coating system (with the use of QuickSeal Fabric Tape).
Seal Trust Perimeter Strip is an adhesive-backed reinforced EPDM membrane installed under the rubber at the perimeter of roofs or at angle changes greater than 4” in height.
Seal Trust Patch Disks are being used for flashing corners, as repair patches, or t-patches and anywhere required on EPDM and most TPO membranes.
Seal Trust Seam Tapes are being used for to bond various roofing membranes together in typical seam applications on low slope roofs.
Seal Trust Flashing Tapes are being used in applications on low slope roofs where pipes, stacks, vents, or corners require flexible flashing products. The Flashing Tapes ensure there is no water infiltration into the roofing system.
Seal Trust Cover Tapes are typically being used for roofing applications such as cover for most metal terminations including gravel stops and drip edges. They are also being used extensively for horizontal patching, seam repairs and seam overlays.
The Seal Trust Pipe Boots are pre-molded roofing accessories used for flashing pipes or stacks protruding from the roof. They are used on single ply membrane installations such as EPDM and TPO low slope roofs. Pipe Boots are installed over vent stacks and pipes usually on flat roof surfaces.
The EPDM Patch Kits are an all-in-one solution to repair small holes or tears in EPDM rubber membranes. The kit can also be used for T-Patches. The patch kit contains Primer, Patches, Seam Roller, and a Scrubbing Pad.