Copyright All Rights Reserved © 2022 | Privacy policy | Sitemap

EPDM & TPO ACCESSORIES

[mk_page_section]

$0.00

Download Product Data Sheet Download Safety Data Sheet

Available in Pints (24/cs), 1 Gallon cans (6/cs), 5 Gallon pails

Our TPO Roof Tape Primer is a clear product specifically formulated as a primer for single ply membranes before the installation of any and all tape products such as seam, flashing and cover tapes along with pipe boots and patch disks . It is a clear product when dried allowing for use with white and black membranes. Tape Primer must be used prior to the installation of all tape products manufactured by Seal Trust™.

TPO Roof Tape Primer Physical Properties:

Color: Clear to neutral
Viscosity (eps): #3 @ 20 rpm=200cps or less
Density (#/GAL.): 7.22# {caa914c204b1119fb3ddf612b08b76802b03c1f9b8e71b690c389a73edd07169}
Solids: 4.8
Flash Point (F): -25F TCC
Base: Synthetic elastomers, resin(s) and filler(s)
Solvent System: Aromatics and Aliphatics Clean-up
Solvent: Mineral spirits, VMP naptha or toluene
Storage: May be stored outside if protected from water. Packaging: Pints (24/cs), Gallons (6/cs), 5 gallon pails

$0.00

Download Product Data Sheet Download Safety Data Sheet

Available in Pints (24/cs), 1 Gallon cans (6/cs), 5 Gallon pails

Our EPDM Roof Tape Primer is a clear product specifically formulated as a primer for single ply membranes before the installation of any and all tape products such as seam, flashing and cover tapes along with pipe boots and patch disks . It is a clear product when dried allowing for use with white and black membranes. Tape Primer must be used prior to the installation of all tape products manufactured by Seal Trust™.

 

$0.00

Download Product Data Sheet Download Safety Data Sheet

Available in black or white

Seal Trust™ EPDM Cover Tapes are cured EPDM cover rubber with specially formulated butyl mastic extruded together for typical roofing applications such as cover for most metal terminations including gravel-stops and drip edge, and extensively used for horizontal patching, seam repairs and seam overlays. This peel and stick product has long term heat and chemical resistance and gives Seal Trust Cover Tape the ability to remain flexible in harsh conditions. Surpassing the industry standards for tack and shear strength our cover tape products provide superior holding power for long life and high durability. Industry standard roofing membrane cleaners and primers must be used to clean the membrane before application. Used with EPDM, TPO, and some PVC roofing membranes

Application Instructions:

Always clean and prime membrane using roofing industry standard products for tape applications such as Seal Trust™ F-Primer or Low VOC Tape Primer. Allow primer to dry before installing tapes. Cover Tape is not for use in flashing applications. Product is a peel and stick cured cover tape. Used for covering metal termination bars, drip edge, and/or all purpose bar in seam applications etc. Apply in primed area by peeling release paper off of 6-12 inches of tape. Stick the tape onto the membrane, while continuing to pull release paper off. Make sure you start on a straight line. Continue pulling release paper off as you move down the pre-primed area. Use sharp scissors for cutting the cover tape. Use metal seam roller with some force perpendicular to tape for proper adhesion.

$0.00

Download Product Data Sheet Download Safety Data Sheet

Available in 1 gallon round paint cans (4 gal/cs)

F-Primer Tape Primer is designed for use with EPDM and TPO roofing installations to enhance the performance and bond of EPDM seam tape and TPO seam tape. This black tape primer requires initial stirring at the start of each day and periodically throughout the day. It is influenced by both temperature and humidity. Strong initial tack allows for immediate bond of tapes to membranes. This product is not intended for use in OTC states.

Application Instructions:

F-Primer should be stirred thoroughly prior to use and then scrubbed into the EPDM surface thoroughly using scrub pads such as Scotch-Brite pads. Change applicator pads frequently and cover an area in excess of the area to be seamed. The use of Seal Trust™ Splice Wash prior to application of this product is recommended on dirty, old membranes to remove all surface contaminations and enhance the performance and bond of EPDM seam adhesives and primers. When used with clean TPO, this primer is a cleaner and primer and the use of Toluene Splice Wash is not required. This product dries black use caution when using with white or colored membranes. Clean up with mineral spirits.

$0.00

Download Product Data Sheet Download Safety Data Sheet

Product Information:

Seal Trust™ Flashing Tapes are uncured EPDM rubber with specially formulated butyl mastic used in applications on roofs where pipes, stacks, vents, or corners require flexible flashing products to ensure no water infiltration into the roofing system. Flashing Tape allows molding or slight stretching of the material then slowly cures to form. With superior tack and peel strengths, our butyl mastic remains flexible in harsh conditions and gives a permanent water tight seal. Industry standard roofing membrane cleaners and primers must be used to clean the surfaces before application.

Application Instructions:

Always clean and prime membrane using roofing industry standard products for tape applications such as Seal Trust™ F-Primer or Low VOC Tape Primer. Allow primer to dry before installing tapes. Field flashing corners, stacks, vents, or other roofing installation procedures where material must be formed. Do not over stretch. Not for use in horizontal seam repairs. Application by experienced roofing professionals recommended.

$0.00

Download Product Data Sheet Download Safety Data Sheet

Available in Black or White
Available in 10.5 oz. tubes

Product Information:

Our EPDM Lap caulk is available in 10.5 oz tubes in both black or white for use in single ply membrane applications such as EPDM or TPO. Standard caulk gun is required for application. Product should not be screed or smoothed after application. This caulk is meant to prevent water infiltration into seams and overlaps prior to the adhesive setting up. Usually 24-48 hours depending on temperature and humidity.

Application Instructions:

Our EPDM Lap Caulk is used when applying splice and/ or bonding adhesives where membrane is overlapped. Prevents initial moisture infiltration before the adhesives are set. Standard caulk gun required for use. Once plastic top is cut you must puncture the tube through the plastic top with a screw driver or long screw or nail to begin application. Do not screed or smooth caulk once applied. All seams that were glued or installed should be caulked at the end of each day.

$0.00

Download Product Data Sheet Download Safety Data Sheet

Available in 1 gallon cans or 5 gallon pails

Latex Bonding Adhesive Product Information:

Seal Trust™ Latex Bonding Adhesive is a white water based adhesive used in adhering EPDM or TPO membranes to various substrates. Product goes on white and dries by evaporation to a clear film.

Application Instructions:

Each gallon covers approximately 100 square feet ONLY. Apply enough adhesive to roof substrate so that membrane will be coated by adhesive when rolled into it. MEMBRANE MUST BE LAID INTO WET ADHESIVE. Wrinkles may be brushed out while adhesive is still wet. ON HOT DAYS, THE ADHESIVE MAY DRY TOO FAST TO USE THIS PROCEDURE. If so apply a thin coat of adhesive to the roof surface and the back of the membrane. For highest initial bond strength join after film becomes tacky. Initial tests indicate that adhesives may be used at temperatures as low as 40F. DO NOT ALLOW MATERIAL TO FREEZE. Meets OTC VOC requirements.

$0.00

Download Product Data Sheet Download Safety Data Sheet

Available in 1 gallon cans or 5 gallon pails

Latex Bonding Adhesive Product Information:

Seal Trust™ Latex Bonding Adhesive is a water based adhesive used in adhering EPDM or TPO membranes to various substrates. Product goes on white and dries by evaporation to a clear film.

Application Instructions:

Each gallon covers approximately 100 square feet ONLY. Apply enough adhesive to roof substrate so that membrane will be coated by adhesive when rolled into it. MEMBRANE MUST BE LAID INTO WET ADHESIVE. Wrinkles may be brushed out while adhesive is still wet. ON HOT DAYS, THE ADHESIVE MAY DRY TOO FAST TO USE THIS PROCEDURE. If so apply a thin coat of adhesive to the roof surface and the back of the membrane. For highest initial bond strength join after film becomes tacky. Initial tests indicate that adhesives may be used at temperatures as low as 40F. DO NOT ALLOW MATERIAL TO FREEZE. Meets OTC VOC requirements.

$0.00

Download Product Data Sheet Download Safety Data Sheet

Available in 1 gallon cans or 5 gallon pails

Product Information:

Seal Trust™ Low VOC Neoprene Bonding Adhesive is designed for use with EPDM and TPO membranes to adhere to insulation boards such as ISO and wood fiber and also to wood, metal, masonry and approved roofing substrates. It may also be used as a general contact bond adhesive for both vertical and horizontal surfaces. It is especially formulated for use in OTC states with Low VOC requirements. May dry faster than regular bonding adhesives due to the solvent content. May be applied using brush, roller or squeegee and also may be sprayed applied using proper equipment.

Application Instructions:

Recommended application instructions for use in EPDM projects are printed on the container label. Care must be taken to ensure adequate adhesive coverage when using some substrates with irregular surface patterns. Stir well before use. May be warmed to room temperature before use to promote easier application. Apply a thin coat to both intended surfaces and let adhesive “dry” until it is tacky to the touch. Mate both surfaces and apply mild pressure. Once the intended surfaces are mated, it will not be possible to reposition them without breaking the bond. Membrane should be rolled when completed. CAUTION. Keep bonding adhesive out of the seam areas at all times!

$0.00

Download Product Data Sheet Download Safety Data Sheet

Available in 1 gallon cans or 5 gallon pails

Product Information:

Seal Trust™ TPO Low VOC Neoprene Bonding Adhesive is designed for use with TPO membranes to adhere to insulation boards such as ISO and wood fiber and also to wood, metal, masonry and approved roofing substrates. It may also be used as a general contact bond adhesive for both vertical and horizontal surfaces. It is especially formulated for use in OTC states with Low VOC requirements. May dry faster than regular bonding adhesives due to the solvent content. May be applied using brush, roller or squeegee and also may be sprayed applied using proper equipment.

Application Instructions:

Recommended application instructions for use in TPO projects are printed on the container label. Care must be taken to ensure adequate adhesive coverage when using some substrates with irregular surface patterns. Stir well before use. May be warmed to room temperature before use to promote easier application. Apply a thin coat to both intended surfaces and let adhesive “dry” until it is tacky to the touch. Mate both surfaces and apply mild pressure. Once the intended surfaces are mated, it will not be possible to reposition them without breaking the bond. Membrane should be rolled when completed. CAUTION. Keep bonding adhesive out of the seam areas at all times!

$0.00

Download Product Data Sheet Download Safety Data Sheet

Available in 1 gallon cans

Product Information:

Splice Wash is a clear solvent used to clean dirt and containments from single ply roof systems. Especially used on old membranes to remove dirt prior to application of tape primers or seam adhesives. Change rags or applicator pads frequently! Do not allow product to puddle on EPDM or TPO for long periods of time. Discarded rags should be disposed of properly and will be a flammable hazard. No smoking or open flames on the roof while using this product. This Low VOC formula is for use in OTC states.

 

Application Instructions:

This product should be scrubbed into the EPDM or TPO surfaces thoroughly to remove surface debris. Change rags frequently. Always clean an area in excess of the area to be covered. When used with clean membranes such as EPDM or TPO this wash is not required. Use solvent resistant gloves when using this product.

$0.00

Download Product Data SheetDownload Safety Data Sheet

Available in 1 gallon cans

Product Information:

Splice Wash is a clear solvent used to clean dirt and containments from single ply roof systems. Especially used on old membranes to remove dirt prior to application of tape primers or seam adhesives. Change rags or applicator pads frequently! Do not allow product to puddle on EPDM or TPO for long periods of time. Discarded rags should be disposed of properly and will be a flammable hazard. No smoking or open flames on the roof while using this product. This Low VOC formula is for use in OTC states.

Application Instructions:

This product should be scrubbed into the EPDM or TPO surfaces thoroughly to remove surface debris. Change rags frequently. Always clean an area in excess of the area to be covered. When used with clean membranes such as EPDM or TPO this wash is not required. Use solvent resistant gloves when using this product.

$0.00

Download Product Data Sheet Download Safety Data Sheet

Available in 1 gallon cans (6/cs)

Low VOC Tape Primer Product Information:

Low VOC Tape Primer is a clear product specifically formulated as a primer for single ply membranes before the installation of any and all tape products such as seam, flashing and cover tapes along with pipe boots and patch disks in all OTC states that require low VOC products. It is a clear product when dried allowing for use with white and black membranes.

Application Instructions:
Always use Low VOC Splice Wash on older, dirty membranes before the use of this product. Change rags frequently when cleaning dirty membranes. Low VOC Tape Primer should be scrubbed into the membrane using scrub pads such as Scotch Brite pads. Allow to dry to the touch depending on temperature and humidity. Always use solvent resistant gloves when applying this product.

$0.00

Download Product Data Sheet Download Safety Data Sheet

Available in 1 gallon cans (6/cs)

Low VOC Tape Primer Product Information:

Low VOC Tape Primer is a clear product specifically formulated as a primer for single ply membranes before the installation of any and all tape products such as seam, flashing and cover tapes along with pipe boots and patch disks in all OTC states that require low VOC products. It is a clear product when dried allowing for use with white and black membranes.

Application Instructions:
Always use Low VOC Splice Wash on older, dirty membranes before the use of this product. Change rags frequently when cleaning dirty membranes. Low VOC Tape Primer should be scrubbed into the membrane using scrub pads such as Scotch Brite pads. Allow to dry to the touch depending on temperature and humidity. Always use solvent resistant gloves when applying this product.

$0.00

Download Product Data Sheet Download Safety Data Sheet

Available in 1 gallon cans or 5 gallon pails

Neoprene Bonding Adhesive Information:

Seal Trust™ Neoprene Bonding Adhesive is designed for use with EPDM and TPO membranes to adhere to insulation boards such as ISO and wood fiber and also to wood, metal, masonry and approved roofing substrates. It may also be used as a general contact bond adhesive for both vertical and horizontal surfaces. May be applied using brush, roller or squeegee and also may be sprayed applied using proper equipment.

Application Instructions:

Recommended application instructions for use in EPDM projects are printed on the container label. Care must be taken to ensure adequate adhesive coverage when using some substrates with irregular surface patterns. Stir well before use. May be warmed to room temperature before use to promote easier application. Apply a thin coat to both intended surfaces and let adhesive “dry” until it is tacky to the touch. Mate both surfaces and apply mild pressure. Once the intended surfaces are mated, it will not be possible to reposition them without breaking the bond. Membrane should be rolled when completed. CAUTION. Keep bonding adhesive out of the seam areas at all times!

$0.00

Download Product Data Sheet Download Safety Data Sheet

Available in 1 gallon cans or 5 gallon pails

Product Information:

Seal Trust™ TPO Neoprene Bonding Adhesive is designed for use with TPO membranes to adhere to insulation boards such as ISO and wood fiber and also to wood, metal, masonry and approved roofing substrates. It may also be used as a general contact bond adhesive for both vertical and horizontal surfaces. May be applied using brush, roller or squeegee and also may be sprayed applied using proper equipment.

Application Instructions:

Recommended application instructions for use in TPO projects are printed on the container label. Care must be taken to ensure adequate adhesive coverage when using some substrates with irregular surface patterns. Stir well before use. May be warmed to room temperature before use to promote easier application. Apply a thin coat to both intended surfaces and let adhesive “dry” until it is tacky to the touch. Mate both surfaces and apply mild pressure. Once the intended surfaces are mated, it will not be possible to reposition them without breaking the bond. Membrane should be rolled when completed. CAUTION. Keep bonding adhesive out of the seam areas at all times!

$0.00

Download Product Data Sheet Download Safety Data Sheet

Available in Black or White

EPDM Patch Disks Information:

Seal Trust™ Patch Disks are uncured EPDM membrane available in black or white with butyl mastic sealer die cut into 8” round disks. Can be used for flashing corners, as repair patches, or t-patches and anywhere required on EPDM, most TPO and some PVC membranes. Membrane must be cleaned prior to installation using Tape Primer.

Application Instructions:

Patch Disks are a multi use product used in inside/outside corners, t-joint covers, and patching or repairs of both EPDM and TPO membranes. Always clean and prime membrane using roofing industry standard products for tape applications such as Seal Trust™ F-Primer or Low VOC Tape Primer. Lap Caulk should be used around all the outer edges of the disk for proper application. Use 3” steel roller for final installation step. Be careful to avoid fish mouths or air bubbles.

$0.00

Download Product Data Sheet Download Safety Data Sheet

Perimeter Strip  Information

Seal Trust™ Perimeter Strip is a 6” wide .045 reinforced EPDM membrane to be installed under the rubber at the perimeter of roofs or at angle changes greater than 4” in height. Perimeter Strip comes with 3” butyl mastic sealer for installation to EPDM membrane using Tape Primer. Installation around the perimeter using 2”or 3” steel plates attached to the roof deck prior to installation of the membrane. Clean the back of the sheet at the area of contact with the butyl mastic. Carefully pull release paper off the mastic and press into place. Then roll membrane into mastic using steel roller for optimum results.

Application Instructions:

Perimeter Strip comes with 3” butyl mastic sealer for installation to EPDM membrane using Tape Primer. Install around the perimeter using 2” or 3” steel plates attached to the roof deck prior to installation of the membrane with proper fasteners spaced per recommended wind uplift area. Clean the back of the sheet at the area of contact with the butyl mastic. Carefully pull release paper off the mastic and press into place. Then roll membrane into mastic using steel roller for optimum results.

$0.00

Download Product Data Sheet Download Safety Data Sheet

Perimeter Strip  Information

Seal Trust™ Perimeter Strip is a 6” wide .045 reinforced EPDM membrane to be installed under the rubber at the perimeter of roofs or at angle changes greater than 4” in height. Perimeter Strip comes with 3” butyl mastic sealer for installation to EPDM membrane using Tape Primer. Installation around the perimeter using 2”or 3” steel plates attached to the roof deck prior to installation of the membrane. Clean the back of the sheet at the area of contact with the butyl mastic. Carefully pull release paper off the mastic and press into place. Then roll membrane into mastic using steel roller for optimum results.

Application Instructions:

Perimeter Strip comes with 3” butyl mastic sealer for installation to EPDM membrane using Tape Primer. Install around the perimeter using 2” or 3” steel plates attached to the roof deck prior to installation of the membrane with proper fasteners spaced per recommended wind uplift area. Clean the back of the sheet at the area of contact with the butyl mastic. Carefully pull release paper off the mastic and press into place. Then roll membrane into mastic using steel roller for optimum results.

$0.00

Download Product Data Sheet Download Safety Data Sheet

Available in Black or White and pipe sizes ranging from 1-3″ or 1-6″

EPDM Pipe Boot  Information

Seal Trust™ Pipe Boots are pre-molded EPDM accessory for flashing pipes or stacks protruding from the roof on single ply membrane installations such as EPDM and TPO. Pipe Boots are installed over vent stacks and pipes usually on flat roof surfaces. The boots all come pre-taped for easy installation with a flange that installs to the membrane in a peel and stick application. The boots come with two piece release paper for easy use.

Application Instructions:

Always clean and prime membrane using roofing industry standard products for tape applications such as Seal Trust™ F-Primer or Low VOC Tape Primer. Usual installation requires primer installed on or about 4-5 inches away from each pipe. Then measure the diameter of the pipe and cut the boot at one size smaller than the pipe (i.e. 4” stack cut at 3” level) and stretching over the pipe. Before pipe boot installation Water Cut Off Caulk should be installed on the pipe for maximum protection. Pipe clamp is provided and required for final step.

$0.00

Download Product Data Sheet Download Safety Data Sheet

QuickSeal Tapes

QuickSeal tapes from Seal Trust™ are pressure sensitive adhesive tapes, which remain flexible even in cold temperatures. QuickSeal tapes may be used on metal roofs to strip in side laps, end laps, and other penetrations prior to the application of a coating system (with the use of QuickSeal Fabric Tape). QuickSeal tapes may also be used on EPDM, TPO, CSPE/Hypalon, CPE, SBS, APP modified, asphalt BURs, all metal roofs, tiles, aluminum, galvanized steel, gypsum board, wood, polyethylene, propylene, polystyrene, fiberglass, brick, concrete, masonry and OSB. This product may be used to repair gutters, chimney flashings, and metal roofs on mobile homes and transport vehicles. QuickSeal tapes make a watertight seal. Can be installed in temperatures down to 20°F (with EPDM Tape Primer). Available in black, white, and fabric. The fabric facer is designed to be coated to match the surrounding roofing surface. The white TPO facer makes QuickSeal tapes UV resistant.

Storage: Store in warehouse without excessive heat. Do NOT store long term on roof.
Shelf Life: 5 years if stored between 60° and 80° F.

$0.00

Download Product Data Sheet Download Safety Data Sheet

QuickSeal Tapes

QuickSeal tapes from Seal Trust™ are pressure sensitive adhesive tapes, which remain flexible even in cold temperatures. QuickSeal tapes may be used on metal roofs to strip in side laps, end laps, and other penetrations prior to the application of a coating system (with the use of QuickSeal Fabric Tape). QuickSeal tapes may also be used on EPDM, TPO, CSPE/Hypalon, CPE, SBS, APP modified, asphalt BURs, all metal roofs, tiles, aluminum, galvanized steel, gypsum board, wood, polyethylene, propylene, polystyrene, fiberglass, brick, concrete, masonry and OSB. This product may be used to repair gutters, chimney flashings, and metal roofs on mobile homes and transport vehicles. QuickSeal tapes make a watertight seal. Can be installed in temperatures down to 20°F (with EPDM Tape Primer). Available in black, white, and fabric. The fabric facer is designed to be coated to match the surrounding roofing surface. The white TPO facer makes QuickSeal tapes UV resistant.

Storage: Store in warehouse without excessive heat. Do NOT store long term on roof.
Shelf Life: 5 years if stored between 60° and 80° F.

$0.00

Download Product Data Sheet Download Safety Data Sheet

Available in black or white

Seal Trust™ Seam Tapes are a butyl sealer used for bonding various roofing membranes together in typical seam applications in the roofing industry. Long term heat and chemical resistance give Seal Trust™ EPDM Seam Tapes the ability to remain flexible in harsh conditions. Surpassing the industry standards for tack and shear strength our Seam Tape products provide superior holding power for long life and high durability. Used with typical roofing membranes such as EPDM, and TPO and some PVC membranes, Seam Tape allows for quick installation without expensive hot air welders. Industry standard roofing membrane cleaners and primers must be used to clean the membrane before application. Available in black or white.

Resistant to: Weather, water & water vapor, (5{caa914c204b1119fb3ddf612b08b76802b03c1f9b8e71b690c389a73edd07169}) acidic or basic solutions
Effected by: Petroleum, grease, oil, solvents, vegetable oils, and animal fats Product
Storage: Store in warehouse without excessive heat. Do NOT store long term on roof.
Shelf Life: 1 year if stored between 60° and 80° F.

$0.00

Download Product Data Sheet Download Safety Data Sheet

Available in 1 gallon cans

Seal Trust™ Splice Adhesive is a black adhesive designed for use as a seam adhesive during the installation of EPDM membrane systems where seaming together two sheets are required. It may also be used as a contact adhesive to bond membranes to suitable substrates as a bonding adhesive substitute. It is a viable alternative for bonding both EPDM and TPO in vertical and horizontal situations.

Application Instructions:

This adhesive must be thoroughly mixed prior to and during use. Recommended application instructions are printed on the container label. Meticulous care must be exercised prior to use of this product in the preparation of the seams to be lapped or spliced. The use of Seal Trust™ Splice Wash is highly recommended along with the use of Seal Trust™ Tape Primer to properly prep the seams prior to splice. Use Seal Trust™ Lap Caulk after the seams have been spliced to protect the seams until total cure has been achieved.

$0.00

Download Product Data Sheet Download Safety Data Sheet

Available in 1 gallon cans or 5 gallon pails

Splice Wash is a clear solvent used to clean dirt and contaminants from single ply roof systems. Especially used on old membranes to remove dirt prior to application of tape primers or seam adhesives. Change rags or applicator pads frequently! Do not allow product to puddle on EPDM for long periods of time. Discarded rags should be disposed of properly and will be a flammable hazard. No smoking or open flames on the roof while using this product. Also available in a Low VOC formula for use in OTC states.

Application Instructions:

The use of Seal Trust™ Toluene Splice Wash prior to application of this product is recommended. This product should be scrubbed into the EPDM surface thoroughly to remove surface debris. Change applicator pads frequently and cover an area in excess of the area to be seamed. No special applicator is required. When used with clean TPO, this primer is a cleaner and primer and the use of Toluene Splice Wash is not required. Solvent resistant gloves should be used when applying this product.

$0.00

Download Product Data Sheet Download Safety Data Sheet

Available in 1 gallon cans or 5 gallon pails

Splice Wash is a clear solvent used to clean dirt and containments from single ply roof systems. Especially used on old membranes to remove dirt prior to application of tape primers or seam adhesives. Change rags or applicator pads frequently! Do not allow product to puddle on EPDM for long periods of time. Discarded rags should be disposed of properly and will be a flammable hazard. No smoking or open flames on the roof while using this product. Also available in a Low VOC formula for use in OTC states.

Application Instructions:

The use of Seal Trust™ Toluene Splice Wash prior to application of this product is recommended. This product should be scrubbed into the EPDM surface thoroughly to remove surface debris. Change applicator pads frequently and cover an area in excess of the area to be seamed. No special applicator is required. When used with clean TPO, this primer is a cleaner and primer and the use of Toluene Splice Wash is not required. Solvent resistant gloves should be used when applying this product.

$0.00

Download Product Data Sheet Download Safety Data Sheet

White Cover Tape

Seal Trust™ TPO Cover Tape is cured EPDM cover rubber with specially formulated butyl mastic extruded together for typical roofing applications such as cover for most metal terminations including gravel-stops and drip edge, and extensively used for horizontal patching, seam repairs and seam overlays. This peel and stick product has long term heat and chemical resistance and gives Seal Trust TPO Cover Tape the ability to remain flexible in harsh conditions. Surpassing the industry standards for tack and shear strength our cover tape products provide superior holding power for long life and high durability. Industry standard roofing membrane cleaners and primers must be used to clean the membrane before application. Used with EPDM, TPO, and some PVC roofing membranes.

Application Instructions:

Always clean and prime membrane using roofing industry standard products for tape applications such as Seal Trust™ F-Primer or Low VOC Tape Primer. Allow primer to dry before installing tapes. TPO Cover Tape is not for use in flashing applications. Product is a peel and stick cured cover tape. Used for covering metal termination bars, drip edge, and/or all purpose bar in seam applications etc. Apply in primed area by peeling release paper off of 6-12 inches of tape. Stick the tape onto the membrane, while continuing to pull release paper off. Make sure you start on a straight line. Continue pulling release paper off as you move down the pre-primed area. Use sharp scissors for cutting the cover tape. Use metal seam roller with some force perpendicular to tape for proper adhesion.

$0.00

Download Product Data Sheet Download Safety Data Sheet

White Lap Caulk
Available in 10.5 oz. tubes

Product Information:

Our TPO lap caulk is available in 10.5 oz tubes in both black or white for use in single ply membrane applications such as EPDM or TPO. Standard caulk gun is required for application. Product should not be screed or smoothed after application. This caulk is meant to prevent water infiltration into seams and overlaps prior to the adhesive setting up. Usually 24-48 hours depending on temperature and humidity.

Application Instructions:

TPO lap caulk is used when applying splice and/ or bonding adhesives where membrane is overlapped. Prevents initial moisture infiltration before the adhesives are set. Standard caulk gun required for use. Once plastic top is cut you must puncture the tube through the plastic top with a screw driver or long screw or nail to begin application. Do not screed or smooth caulk once applied. All seams that were glued or installed should be caulked at the end of each day.

$0.00

Download Product Data Sheet Download Safety Data Sheet

White Patch Disks

Product Information:

Seal Trust™ TPO Patch Disks are uncured roofing membrane available in black or white with butyl mastic sealer die cut into 8” round disks. Can be used for flashing corners, as repair patches, or t-patches and anywhere required on EPDM, most TPO and some PVC membranes. Membrane must be cleaned prior to installation using Tape Primer.

Application Instructions:

TPO Patch Disks are a multi use product used in inside/outside corners, t-joint covers, and patching or repairs of both EPDM and TPO membranes. Always clean and prime membrane using roofing industry standard products for tape applications such as Seal Trust™ F-Primer or Low VOC Tape Primer. Lap Caulk should be used around all the outer edges of the disk for proper application. Use 3” steel roller for final installation step. Be careful to avoid fish mouths or air bubbles.

$0.00

Download Product Data Sheet Download Safety Data Sheet

White in color and pipe sizes ranging from 1-3″ or 1-6″

Product Information

Seal Trust™ TPO Pipe Boot is a pre-molded roofing accessory for flashing pipes or stacks protruding from the roof on single ply membrane installations such as EPDM and TPO. Pipe Boots are installed over vent stacks and pipes usually on flat roof surfaces. The boots all come pre-taped for easy installation with a flange that installs to the membrane in a peel and stick application. The boots come with two piece release paper for easy use.

Application Instructions:

Always clean and prime membrane using roofing industry standard products for tape applications such as Seal Trust™ F-Primer or Low VOC Tape Primer. Usual installation requires primer installed on or about 4-5 inches away from each pipe. Then measure the diameter of the pipe and cut the boot at one size smaller than the pipe (i.e. 4” stack cut at 3” level) and stretching over the pipe. Before pipe boot installation Water Cut Off Caulk should be installed on the pipe for maximum protection. Pipe clamp is provided and required for final step.

$0.00

Download Product Data Sheet Download Safety Data Sheet

White Seam Tapes

Seal Trust™ TPO Seam Tapes are a butyl sealer used for bonding various roofing membranes together in typical seam applications in the roofing industry. Long term heat and chemical resistance gives Seal Trust™ Seam Tape the ability to remain flexible in harsh conditions. Surpassing the industry standards for tack and shear strength our Seam Tape products provide superior holding power for long life and high durability. Used with typical roofing membranes such as EPDM, and TPO and some PVC membranes, Seam Tape allows for quick installation without expensive hot air welders. Industry standard roofing membrane cleaners and primers must be used to clean the membrane before application. Available in black or white.

Resistant to: Weather, water & water vapor, (5{caa914c204b1119fb3ddf612b08b76802b03c1f9b8e71b690c389a73edd07169}) acidic or basic solutions
Effected by: Petroleum, grease, oil, solvents, vegetable oils, and animal fats Product
Storage: Store in warehouse without excessive heat. Do NOT store long term on roof.
Shelf Life: 1 year if stored between 60° and 80° F.

$0.00

Download Product Data Sheet Download Safety Data Sheet

Available in 10.5 oz. fiber caulk tubes or 5 gallon pails.

Seal Trust™ Water Cut-Off Mastic is a gray solvent based caulk designed to be used under the membrane to prevent water infiltration. Meets OTC VOC requirements.

Physical Properties:

Color: Gray
Viscosity (eps): 40# .104= 15-20 sec./20 gms.
Sievers Rheometer Density (#/GAL.): 11.0#
{caa914c204b1119fb3ddf612b08b76802b03c1f9b8e71b690c389a73edd07169} Solids: 86
Flash Point (F): 14 F TCC
Base: Synthetic elastomers, resin(s) and filler(s)
Solvent System: Aliphatic Clean-up
Solvent: Mineral spirits, VMP naptha, kerosene
Storage: May be stored outside if protected from water.
Packaging: 5 gallon pails, 10.5 oz. fiber caulk tubes (10 or 25 tubes/ctn)

$0.00

Download Product Data Sheet Download Safety Data Sheet

Available in 10.5 oz. fiber caulk tubes or 5 gallon pails.

Seal Trust™ Water Cut-Off Mastic is a gray solvent based caulk designed to be used under the membrane to prevent water infiltration. Meets OTC VOC requirements.

Physical Properties:

Color: Gray
Viscosity (eps): 40# .104= 15-20 sec./20 gms.
Sievers Rheometer Density (#/GAL.): 11.0#
{caa914c204b1119fb3ddf612b08b76802b03c1f9b8e71b690c389a73edd07169} Solids: 86
Flash Point (F): 14 F TCC
Base: Synthetic elastomers, resin(s) and filler(s)
Solvent System: Aliphatic Clean-up
Solvent: Mineral spirits, VMP naptha, kerosene
Storage: May be stored outside if protected from water.
Packaging: 5 gallon pails, 10.5 oz. fiber caulk tubes (10 or 25 tubes/ctn)

[/mk_page_section]