Copyright All Rights Reserved © 2021 | Privacy policy | Sitemap

EPDM & TPO Roofing Products Manufacturer

    Flashing Tapes

    flashing tapes
    flashing tapes

    Flashing Tapes

    $0.00

    Download Product Data Sheet Download Safety Data Sheet

    Product Information:

    Seal Trust™ Flashing Tapes are uncured EPDM rubber with specially formulated butyl mastic used in applications on roofs where pipes, stacks, vents, or corners require flexible flashing products to ensure no water infiltration into the roofing system. Flashing Tape allows molding or slight stretching of the material then slowly cures to form. With superior tack and peel strengths, our butyl mastic remains flexible in harsh conditions and gives a permanent water tight seal. Industry standard roofing membrane cleaners and primers must be used to clean the surfaces before application.

    Application Instructions:

    Always clean and prime membrane using roofing industry standard products for tape applications such as Seal Trust™ F-Primer or Low VOC Tape Primer. Allow primer to dry before installing tapes. Field flashing corners, stacks, vents, or other roofing installation procedures where material must be formed. Do not over stretch. Not for use in horizontal seam repairs. Application by experienced roofing professionals recommended.

    SKU: http://sealtrustroofing.com/wp-content/uploads/2018/08/tpo-seam-tape.png Category: Tags: , , , , , , , , ,

    Resistant to: Weather, water & water vapor, (5{caa914c204b1119fb3ddf612b08b76802b03c1f9b8e71b690c389a73edd07169}) acidic or basic solutions
    Effected by: Petroleum, grease, oil, solvents, vegetable oils, and animal fats
    Product Storage: Store in warehouse without excessive heat. Do NOT store long term on roof.
    Shelf Life: 1 year if stored between 60° and 80° F.

    Flashing Tapes Physical Properties:

    Color: Black Solids: 100{caa914c204b1119fb3ddf612b08b76802b03c1f9b8e71b690c389a73edd07169}
    Odor: Slight Hydrocarbon
    Penetration: (ASTM D 217) : 100/130 mm
    Volatile: {caa914c204b1119fb3ddf612b08b76802b03c1f9b8e71b690c389a73edd07169} by Volume: None
    Adhesion: To most clean, dry substrates/surfaces

    Weight-201808--. lbs
    Dimensions-201808--. × -201808--. × -201808--. in

    Related products

    tpo-low-voc-tape-primer-tpo-epdm
    $0.00
    Low VOC Tape Primer

    Download Product Data Sheet Download Safety Data Sheet

    Available in 1 gallon cans (6/cs)

    Low VOC Tape Primer Product Information:

    Low VOC Tape Primer is a clear product specifically formulated as a primer for single ply membranes before the installation of any and all tape products such as seam, flashing and cover tapes along with pipe boots and patch disks in all OTC states that require low VOC products. It is a clear product when dried allowing for use with white and black membranes.

    Application Instructions:
    Always use Low VOC Splice Wash on older, dirty membranes before the use of this product. Change rags frequently when cleaning dirty membranes. Low VOC Tape Primer should be scrubbed into the membrane using scrub pads such as Scotch Brite pads. Allow to dry to the touch depending on temperature and humidity. Always use solvent resistant gloves when applying this product.

    cover-tapes-epdm-op
    $0.00
    Cover Tape

    Download Product Data Sheet Download Safety Data Sheet

    Available in black or white

    Seal Trust™ EPDM Cover Tapes are cured EPDM cover rubber with specially formulated butyl mastic extruded together for typical roofing applications such as cover for most metal terminations including gravel-stops and drip edge, and extensively used for horizontal patching, seam repairs and seam overlays. This peel and stick product has long term heat and chemical resistance and gives Seal Trust Cover Tape the ability to remain flexible in harsh conditions. Surpassing the industry standards for tack and shear strength our cover tape products provide superior holding power for long life and high durability. Industry standard roofing membrane cleaners and primers must be used to clean the membrane before application. Used with EPDM, TPO, and some PVC roofing membranes

    Application Instructions:

    Always clean and prime membrane using roofing industry standard products for tape applications such as Seal Trust™ F-Primer or Low VOC Tape Primer. Allow primer to dry before installing tapes. Cover Tape is not for use in flashing applications. Product is a peel and stick cured cover tape. Used for covering metal termination bars, drip edge, and/or all purpose bar in seam applications etc. Apply in primed area by peeling release paper off of 6-12 inches of tape. Stick the tape onto the membrane, while continuing to pull release paper off. Make sure you start on a straight line. Continue pulling release paper off as you move down the pre-primed area. Use sharp scissors for cutting the cover tape. Use metal seam roller with some force perpendicular to tape for proper adhesion.

    pipe-boot-epdm
    Pipe Boot
    $0.00
    Pipe Boot

    Download Product Data Sheet Download Safety Data Sheet

    Available in Black or White and pipe sizes ranging from 1-3″ or 1-6″

    EPDM Pipe Boot  Information

    Seal Trust™ Pipe Boots are pre-molded EPDM accessory for flashing pipes or stacks protruding from the roof on single ply membrane installations such as EPDM and TPO. Pipe Boots are installed over vent stacks and pipes usually on flat roof surfaces. The boots all come pre-taped for easy installation with a flange that installs to the membrane in a peel and stick application. The boots come with two piece release paper for easy use.

    Application Instructions:

    Always clean and prime membrane using roofing industry standard products for tape applications such as Seal Trust™ F-Primer or Low VOC Tape Primer. Usual installation requires primer installed on or about 4-5 inches away from each pipe. Then measure the diameter of the pipe and cut the boot at one size smaller than the pipe (i.e. 4” stack cut at 3” level) and stretching over the pipe. Before pipe boot installation Water Cut Off Caulk should be installed on the pipe for maximum protection. Pipe clamp is provided and required for final step.

    latex-bonding-adhesive-tpo-lba-200-5
    $0.00
    Latex Bonding Adhesive

    Download Product Data Sheet Download Safety Data Sheet

    Available in 1 gallon cans or 5 gallon pails

    Latex Bonding Adhesive Product Information:

    Seal Trust™ Latex Bonding Adhesive is a water based adhesive used in adhering EPDM or TPO membranes to various substrates. Product goes on white and dries by evaporation to a clear film.

    Application Instructions:

    Each gallon covers approximately 100 square feet ONLY. Apply enough adhesive to roof substrate so that membrane will be coated by adhesive when rolled into it. MEMBRANE MUST BE LAID INTO WET ADHESIVE. Wrinkles may be brushed out while adhesive is still wet. ON HOT DAYS, THE ADHESIVE MAY DRY TOO FAST TO USE THIS PROCEDURE. If so apply a thin coat of adhesive to the roof surface and the back of the membrane. For highest initial bond strength join after film becomes tacky. Initial tests indicate that adhesives may be used at temperatures as low as 40F. DO NOT ALLOW MATERIAL TO FREEZE. Meets OTC VOC requirements.

    $0.00
    Splice Adhesive

    Download Product Data Sheet Download Safety Data Sheet

    Available in 1 gallon cans

    Seal Trust™ Splice Adhesive is a black adhesive designed for use as a seam adhesive during the installation of EPDM membrane systems where seaming together two sheets are required. It may also be used as a contact adhesive to bond membranes to suitable substrates as a bonding adhesive substitute. It is a viable alternative for bonding both EPDM and TPO in vertical and horizontal situations.

    Application Instructions:

    This adhesive must be thoroughly mixed prior to and during use. Recommended application instructions are printed on the container label. Meticulous care must be exercised prior to use of this product in the preparation of the seams to be lapped or spliced. The use of Seal Trust™ Splice Wash is highly recommended along with the use of Seal Trust™ Tape Primer to properly prep the seams prior to splice. Use Seal Trust™ Lap Caulk after the seams have been spliced to protect the seams until total cure has been achieved.

    TPO Patch Disks
    $0.00
    TPO Patch Disks

    Download Product Data Sheet Download Safety Data Sheet

    White Patch Disks

    Product Information:

    Seal Trust™ TPO Patch Disks are uncured roofing membrane available in black or white with butyl mastic sealer die cut into 8” round disks. Can be used for flashing corners, as repair patches, or t-patches and anywhere required on EPDM, most TPO and some PVC membranes. Membrane must be cleaned prior to installation using Tape Primer.

    Application Instructions:

    TPO Patch Disks are a multi use product used in inside/outside corners, t-joint covers, and patching or repairs of both EPDM and TPO membranes. Always clean and prime membrane using roofing industry standard products for tape applications such as Seal Trust™ F-Primer or Low VOC Tape Primer. Lap Caulk should be used around all the outer edges of the disk for proper application. Use 3” steel roller for final installation step. Be careful to avoid fish mouths or air bubbles.